SN: snow in METAR and TAF

Tafrob editorial team · Updated · 6 min read

Short answer

SN is snow: ice crystals, mostly branched six-pointed stars, falling alone or stuck together as flakes. A sign gives the intensity: -SN light, SN moderate, +SN heavy. US observers set it from visibility, with heavy snow at 1/4 statute mile or less, while WMO-No. 782 uses the water equivalent and CAP 746 the accumulation rate. SHSN is snow showers and BLSN blowing snow.

Key points

  • SN is falling snow: branched ice crystals, alone or agglomerated into flakes.
  • FMH-1 sets snow intensity from visibility: light above 1/2 statute mile, moderate above 1/4 to 1/2, heavy 1/4 or less.
  • WMO-No. 782 uses the liquid water equivalent: heavy snow is 5.0 mm per hour or more.
  • CAP 746 uses accumulation: heavy snow is more than 4 cm per hour.
  • SHSN is snow from convective cloud; BLSN is snow lifted by the wind, with or without snow falling.
  • US remarks give snow depth (4/sss), hourly increase (SNINCR) and water equivalent on the ground (933RRR).
Finnair Airbus A319 on approach with the landing gear down, snowflakes falling in front of the aircraft
Photo: Lentokonefani, CC BY-SA 4.0, via Wikimedia Commons

Snow in the present weather group

FMH-1 defines snow as precipitation of snow crystals, mostly branched in the form of six-pointed stars. WMO-No. 782 describes it as single or agglomerated ice crystals and notes that, at temperatures near freezing, the crystals stick together into flakes that can exceed 25 mm across. Its effects range from a few flakes to a runway closed by accumulation.

SN is coded in the present weather group:

Code Meaning
-SN Light snow
SN Moderate snow
+SN Heavy snow
-SHSN, SHSN, +SHSN Snow showers
TSSN Thunderstorm with snow
-RASN Light rain and snow, rain dominant
-SNRA Light snow and rain, snow dominant
BLSN Blowing snow
DRSN Low drifting snow

Intensity by visibility in US reports

FMH-1 sets the intensity of snow, snow pellets and drizzle from the reported surface visibility when they occur alone (Table 8-4). The FAA AIM, section 7-1-17, gives the same bands:

Intensity Visibility
Light More than 1/2 statute mile
Moderate More than 1/4 mile, up to 1/2 mile
Heavy 1/4 mile or less

The rule applies when snow is the only obscuring phenomenon. If fog or haze also reduces the visibility, the observer has to judge the snow itself. The consequence for decoding is direct: a US METAR with +SN always has a visibility of 1/4 mile or less when snow is alone, and a METAR showing -SN with 3/4 mile is consistent with the rule.

Intensity by rate in WMO and UK rules

WMO-No. 782 uses the liquid water equivalent of the snow, with a guide to visibility:

Intensity Water equivalent Visibility, generally
Light Below 1.0 mm per hour Not below 1000 m
Moderate 1.0 to below 5.0 mm per hour 400 to 1000 m
Heavy 5.0 mm per hour or more Below 400 m

CAP 746 (section 4.95) states that there is no internationally agreed scale and gives the UK practice, based on the rate of accumulation: light snow up to 0.5 cm per hour, moderate more than 0.5 to 4 cm per hour, heavy more than 4 cm per hour. CAP 746 adds a visual guide and notes that heavy snow often produces white-out conditions.

The three methods do not measure the same thing. One inch of fresh snow can contain very different amounts of water depending on its density, so a rate in centimetres and a rate in millimetres of water do not convert into each other. The general rules for the signs are on the intensity and vicinity page.

Light snow is not harmless

WMO-No. 782 attaches a warning to light snow: as little as 0.8 mm of snow or ice on the upper surface of a wing can cause a loss of lift. A report of -SN is therefore not an invitation to skip de-icing. Snow also hides runway markings, changes braking action and can build up on parked aircraft, which is why the runway state group used in Europe reports deposits and their depth.

SN, SHSN and TSSN

As with rain, the descriptor tells the type of cloud.

  • SN falls from layered cloud and tends to be steady and widespread.
  • SHSN falls from convective cloud. FMH-1 allows SH with snow, and a snow shower can bring the visibility down to a few hundred metres within minutes, then clear just as fast. The SH showers page explains the descriptor.
  • TSSN is snow with a thunderstorm. NWS Instruction 10-813 lists TSSN and gives the TAF example TSSNRA.

Mixed snow

Several types can share one group, the dominant first, under one sign. FMH-1 allows up to three types per group. -RASN is light rain and snow with rain dominant; -SNRA is the reverse. The FAA AIM gives +SHRASNPL, heavy rain showers with snow and ice pellets, and notes that the sign refers to the dominant rain. NWS Instruction 10-813 adds SHSNPL and FZRASNPL.

When freezing rain is part of the mix, NWS Instruction 10-813 places the freezing type first with its own intensity, so heavy snow with light freezing rain is coded -FZRASN. Ice pellets in the mix are covered on the PL and IC page.

Falling snow or blowing snow

Wind can lift snow that has already fallen. When it reaches 2 m (6 feet) or more, the code is BLSN; below that height it is DRSN. FMH-1 states that no intensity is given to BLSN, and that if the observer cannot tell whether snow is also falling, BLSN is reported.

CAP 746 (sections 4.72 and 4.73) gives the combination: SN BLSN when snow is falling and blowing snow is also present, and only +BLSN when heavy blowing snow hides whether snow is falling. The two descriptors are explained on the DR and BL page.

A schematic report shows the two together:

METAR KXYZ 150953Z 33025G35KT 1/4SM SN BLSN VV005 M09/M11 A2987

It reads: wind from 330 degrees at 25 knots gusting 35, visibility 1/4 statute mile, moderate snow and blowing snow, vertical visibility 500 feet, temperature minus 9 °C. The visibility table of FMH-1 applies to snow occurring alone; here blowing snow also reduces the visibility, so the sign reflects the observer's judgement of the falling snow.

Snow in US remarks

US reports add snow data in the remarks section.

  • Begin and end times. SNB20E55 means snow began at 20 minutes past the hour and ended at 55.
  • Snow increasing rapidly. FMH-1 adds SNINCR when the snow depth increases by 1 inch or more in the past hour: SNINCR 2/10 means 2 inches in the past hour, 10 inches on the ground.
  • Snow depth. The group 4/sss gives the total depth in whole inches: 4/021 is 21 inches.
  • Water equivalent. 933RRR gives the water equivalent of the snow on the ground in the 1800 UTC report when the depth is 2 inches or more: 933036 is 3.6 inches.

These groups are listed with the other numeric remarks on the additive data groups page.

Snow in a TAF

Snow appears in forecasts with the same codes. NWS Instruction 10-813 gives a TAF example with snow showers and freezing fog, 1/2SM SHSN FZFG OVC003, and allows DRSN and BLSN. Because snow intensity in US practice follows visibility, a forecast of +SN is in effect also a forecast of very low visibility.

In real reports

The "In real reports" box on this page shows the share of METARs in the NOAA Aviation Weather Center sample collected for this site that contain SN, with the most frequent combinations. Snow is seasonal and regional, so a sample collected over a short period in late autumn reflects only the stations where it was already snowing.

Method and limits

Definitions and rules are taken from WMO-No. 782 (2025 edition), CAP 746 (sections 4.72, 4.73, 4.94 to 4.96), FMH-1 (2019, Table 8-4, chapter 8 coding rules and chapter 12 remarks), NWS Instruction 10-813 (October 2024) and the FAA AIM, chapter 7, section 1. The three intensity scales use different quantities (visibility, water equivalent, accumulation) and do not convert into one another. The comparison signs of FMH-1 Table 8-4 are lost in the text extraction of the PDF used here; the bands above are confirmed by the FAA AIM, section 7-1-17. The KXYZ line is a schematic example, not a real report. The box counts SN in the text of the METARs, so SHSN, BLSN and mixed groups may be included depending on how the statistic key counts them.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does +SN mean in a METAR?

+SN means heavy snow. In US reports, snow alone is heavy when the visibility is 1/4 statute mile or less. WMO-No. 782 sets heavy snow at 5.0 mm per hour of water equivalent or more, with visibility generally below 400 m.

Why is snow intensity based on visibility in the US?

Snow is hard to measure quickly by weight, and its effect on flying is mostly the loss of visibility. FMH-1 therefore sets the intensity of snow occurring alone from the reported surface visibility, in the same table as drizzle and snow pellets.

What is the difference between SN and SHSN?

SN falls from layered cloud and tends to be steady. SHSN falls from convective cloud: it starts and stops abruptly and changes intensity quickly, with clearer spells between showers. The descriptor tells the type of cloud, not the amount of snow.

What does SN BLSN mean?

Snow is falling and the wind is also lifting snow from the ground to 2 m or more. CAP 746 reports both groups when both are present. When heavy blowing snow hides whether snow is falling, only +BLSN is reported.

What does SNINCR 2/10 mean?

It is a US remark: the snow depth increased by 2 inches in the past hour and the total depth on the ground is 10 inches. FMH-1 adds it when the depth increases by 1 inch or more in the past hour.

Sources

  1. World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition
  2. UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
  3. Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FCM-H1-2019)
  4. National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024), Appendix B
  5. Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1