FM group in a TAF: the FROM change group explained

Tafrob editorial team · Updated · 7 min read

Short answer

FM means FROM. FM followed by day, hour and minute (FMddhhmm) starts a new self-contained part of the forecast at that exact time. It replaces everything written before it, so wind, visibility, weather and cloud must all be restated. The conditions then hold until the next FM or the end of validity.

Key points

  • FM is followed by a six digit time in UTC (day, hour, minute) and takes effect at that moment.
  • An FM supersedes all earlier conditions, so every element must be repeated in the group.
  • Only significant weather may be left out, and only when none is expected.
  • FM is for rapid, lasting changes; BECMG covers gradual ones and TEMPO covers short fluctuations.
An approaching thunderstorm with a lead gust front forming a flat shelf cloud over open ground
Photo: Unknown author, Public domain, via Wikimedia Commons

What FM does in a TAF

FM stands for FROM. It splits the forecast into separate periods: everything after the FM group applies from the stated time, and nothing written earlier carries over. Regulation (EU) 2017/373 describes it as a division of the forecast period into self-contained periods, where FM is followed by a six-figure group giving the day, hour and minutes in UTC, and the elements before it are superseded. NWS Instruction 10-813 says the same thing in operational terms: the conditions in an FM group apply until the next FM group or the end of the valid period.

That "self-contained" idea is the key to reading it. Once you reach an FM, you stop carrying the base forecast forward. The FM line is the whole forecast for that period, and you read it as if it were a short TAF of its own. The pillar page How to read a TAF shows where change groups sit in the overall order; this page goes deeper on FM only.

The time format: day, hour and minute

An FM group is written FM followed by six digits: FMddhhmm without separators. Using the NWS sample, FM030230 is the 3rd of the month at 0230 UTC. The same sample goes on to FM030500, the 3rd at 0500 UTC.

Two details follow from the rules in the sources.

  • The time is a single moment, not a period. NWS Instruction 10-813 says FM is a single time to the nearest minute if the change can be forecast to that accuracy. Whole hours are acceptable, but the instruction states that higher resolution is preferred.
  • The date part is easy to misread. The FAA Aeronautical Information Manual adds a caution in the key to its sample TAF: users should confirm the date and time, and FM 10 0000 is 0000Z on the 10th, and must not be confused with 1000Z.

Transport Canada writes the group with a trailing Z in its sample, for example FM290130Z, and explains that FM280930 means the 28th at 0930Z. The ICAO and US formats in the other sources have no Z. If you need a converter for the hours, the Zulu time converter is on the site.

When to use FM

The NWS instruction says FM is used when the prevailing conditions change significantly over a period of less than one hour. Transport Canada describes FM as a rapid and permanent change, followed by a complete forecast with all elements. So the reading is the same in both systems: FM is for a change that happens quickly and stays.

NWS Instruction 10-813 lists the situations that should make the forecaster consider starting a new FM group:

  • the start or end of low level wind shear;
  • a wind change of 30 degrees or more with a speed of 12 knots or more, or a change that crosses a critical threshold;
  • the start or end of hail, freezing precipitation or ice pellets;
  • conditions crossing the Categorical Amendment Criteria thresholds;
  • the start or end of a thunderstorm.

The instruction also gives a guide on volume: generally no more than six FM groups in a TAF, or eight for 30 hour TAFs, excluding TEMPO groups. This is guidance for forecasters, and it explains why a US TAF rarely has a long chain of changes. For the timing of the period they sit in, see TAF validity period.

Everything must be repeated

Because an FM supersedes what came before, nothing from the earlier lines is assumed to continue. NWS Instruction 10-813 spells out the elements that must be repeated in each FM group: wind, visibility, significant weather, clouds, obscurations and, when expected, non-convective low level wind shear. The only element that may be dropped is significant weather, and only if none is expected.

Transport Canada says the same: FM is followed by a complete forecast with all elements.

The practical point is the wind. When the wind has not changed, it is still written again. The NWS instruction shows this in its sample for KAPN, where the wind is 31010KT in both the FM010320 and FM010500 lines even though it did not change between them.

Sourced examples

The two examples below are taken from NWS Instruction 10-813. The source prints a trailing ellipsis after the last group of each example, which is removed here. The lines are shown on separate rows because NWS TAFs start each FM and TEMPO group on a new line.

KDSM 022336Z 0300/0400 20015KT P6SM BKN015
     FM030230 29020G35KT 1SM +SHRA OVC005
      TEMPO 0303/0304 30030G45KT 3/4SM -SHSN
     FM030500 31010G20KT P6SM SCT025

Read it step by step. The first line is the base forecast for the 3rd, valid for the whole of the 3rd (0300/0400), with a 15 knot wind, visibility above 6 statute miles and a broken layer at 1,500 feet. At 0230 UTC the FM line takes over completely: wind from 290 degrees at 20 knots gusting 35, visibility 1 mile in heavy rain showers, overcast at 500 feet. The TEMPO line modifies that FM period for one hour. At 0500 UTC another FM replaces it all, and the TEMPO that belonged to the earlier period no longer applies. The TEMPO line is covered in the TEMPO page.

KAPN 312330Z 0100/0200 13008KT P6SM SCT030
     FM010320 31010KT 3SM -SHSN BKN015
     FM010500 31010KT 1/4SM +SHSN VV007

Here the wind stays at 310 degrees and 10 knots in the second FM, yet it is repeated, which matches the rule that all elements are required. The weather got worse at 0500 UTC: visibility fell to a quarter of a mile in heavy snow showers with a vertical visibility of 700 feet.

Layout and the NWS format

NWS Instruction 10-813 sets a layout rule that you will see in US TAFs: each FM group starts on a new line and is indented five spaces. TEMPO groups are indented six spaces. The layout does not change the meaning, but it makes the structure easier to read than a single long line.

A full US example from the FAA Aeronautical Information Manual, which is also the sample used in the key of that manual, shows several FM groups in sequence:

KPIT 091730Z 0918/1024 15005KT 5SM HZ FEW020 WS010/31022KT
FM091930 30015G25KT 3SM SHRA OVC015
TEMPO 0920/0922 1/2SM +TSRA OVC008CB
FM100100 27008KT 5SM SHRA BKN020 OVC040
PROB30 1004/1007 1SM -RA BR
FM101015 18005KT 6SM -SHRA OVC020
BECMG 1013/1015 P6SM NSW SKC

The base forecast runs from 1800 UTC on the 9th. At 1930 UTC the first FM replaces it. At 0100 UTC on the 10th a second FM takes over, and at 1015 UTC on the 10th a third FM begins. Notice that the BECMG at the end appears in an FAA sample even though NWS TAFs do not use BECMG in their own forecasts. The sample illustrates the code, not NWS practice, which is why it is not a model for NWS style. The structure of BECMG is on the BECMG page.

Comparison across authorities

Point NWS (US) EU Regulation 2017/373 Transport Canada
Time format FMddhhmm, nearest minute if forecastable FM followed by six figures ddhhmm UTC FMddhhmm with a Z in the sample
Meaning Prevailing conditions change over less than one hour Self-contained period, earlier elements superseded Rapid and permanent change
Content after FM All elements repeated Self-contained period Complete forecast with all elements
Number of groups Generally no more than 6 (8 for 30 hour TAFs), excluding TEMPO Not set in the cited text Not set in the cited text

The EU template adds examples with the form FM051230 15015KMH 9999 BKN020, together with the same line in knots as FM051230 15008KT 9999 BKN020. These show the wind unit that may be used (kilometres per hour) and the usual layout of wind, visibility and cloud after the time.

Common mistakes

  • Reading the six digits as hour, minute and seconds. The first two digits are the day.
  • Carrying an earlier TEMPO, or an earlier cloud layer, into an FM period. The FM supersedes it.
  • Assuming the wind is unchanged because it is not repeated. Under the NWS rules it must be repeated, so if it is absent in a US TAF something is wrong with the report.
  • Treating FM as gradual. A change that takes hours belongs in BECMG, and a short fluctuation belongs in TEMPO. A side-by-side view is in TEMPO vs BECMG vs FM.

The TAF decoder splits a TAF into its periods, and the TAF statistics page contains the figures on FM use from the dataset behind this site.

Method and limits

Every rule here comes from NWS Instruction 10-813, Regulation (EU) 2017/373, the Transport Canada AIM MET section and the FAA Aeronautical Information Manual. The NWS and FAA lines are quoted from those documents, with the trailing ellipsis of the NWS examples removed. The EU and Canadian texts cited here set no limit on the number of FM groups, so the table says so. The FAA sample contains BECMG although the AIM states that the NWS does not use it, so it is used here only to show the code.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does FM mean in a TAF?

FM means FROM. It is followed by the day, hour and minute in UTC, such as FM030230, and it marks the start of a new self-contained part of the forecast. The Regulation (EU) 2017/373 template and NWS Instruction 10-813 both describe the conditions after FM as superseding everything before it.

Do I need to repeat the wind after FM?

Yes. NWS Instruction 10-813 requires all elements to be repeated in an FM group: wind, visibility, significant weather, clouds, obscurations and non-convective low level wind shear when expected. Only significant weather is omitted when none is expected. The sample FM010500 line repeats a wind that did not change.

Is FM030230 the 3rd at 0230 or the 30th at 2300?

It is the 3rd at 0230 UTC. The digits are day, hour, minute in that order. The FAA AIM warns about the same trap with FM 10 0000, which is 0000Z on the 10th and not 1000Z, so always confirm the date and the time.

When should I use FM instead of BECMG or TEMPO?

Use FM when prevailing conditions change significantly over less than one hour, according to NWS Instruction 10-813. Transport Canada also describes FM as a rapid and permanent change. A gradual change belongs in BECMG, and a fluctuation of under one hour belongs in TEMPO.

Sources

  1. National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024)
  2. European Union (EUR-Lex) (2017). Commission Implementing Regulation (EU) 2017/373, Annex V (Part-MET), aerodrome forecasts and TAF template
  3. Transport Canada (2025). TC AIM, MET section 7.0 Aerodrome forecasts (TAFs)
  4. Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1