TAF vs METAR: what each report tells you

Tafrob editorial team · Updated · 6 min read

Short answer

A METAR is an observation: the weather measured at an aerodrome at one moment, issued every hour or half hour. A TAF is a forecast: the most probable conditions expected over the next 24 or 30 hours, with change groups, issued every six hours. They share most codes but differ in timing, area and content, so pilots read the latest METAR against the current TAF.

Key points

  • A METAR reports what was observed; a TAF forecasts what is expected.
  • METARs are issued hourly or half hourly, with SPECI in between; TAFs every 6 hours for long validities, with amendments.
  • A TAF covers a period and uses change groups; a METAR is a snapshot, at most with a short TREND.
  • Temperature, dew point, pressure and RVR are in the METAR, not in a standard TAF.
  • Some codes differ: US TAFs use SKC and P6SM where METARs use CLR and 10SM.
  • Compare the latest METAR with the current TAF to check whether the forecast is on track.
The operator interface of an Automated Surface Observing System at Ely Airport, Nevada
Photo: Famartin, CC BY-SA 3.0, via Wikimedia Commons

Observation and forecast

The METAR and the TAF are the two reports a pilot reads most often for an aerodrome, and they look alike: the same station identifier, the same wind group, the same weather abbreviations, the same cloud layers. They answer different questions.

  • The METAR says what the weather is. WMO-No. 782 defines it as an aerodrome routine meteorological report. It describes conditions observed at one time, by a human observer, an automated system, or both.
  • The TAF says what the weather is expected to be. WMO-No. 782 describes it as the forecaster's assessment of the most likely values and their significant changes during the forecast period.

The Transport Canada AIM puts the METAR as describing actual weather at a specific location and time as observed from the ground, and the TAF as the most probable weather conditions expected at an aerodrome, with their most probable time of occurrence. The METAR pillar page and the TAF pillar page decode each report group by group.

Side by side

METAR TAF
Nature Observation Forecast
Time covered One moment, the observation time A validity period, up to 30 hours
Routine issue Hourly or half hourly (WMO-No. 782) Every 6 hours for 12 to 30 hour TAFs, every 3 hours for shorter ones (WMO-No. 782)
Unscheduled issue SPECI when criteria are met TAF AMD when the forecast is no longer representative
Time group Observation time, DDHHMMZ Issue time, then validity DDHH/DDHH
Changes TREND appended in some countries (2 hours) FM, BECMG, TEMPO, PROB groups
Temperature and dew point Always Only the optional TX and TN groups
Pressure (QNH or altimeter) Always Not in civil TAFs
RVR, runway state, remarks Yes, where applicable No
Wind shear Observed shear on a runway, WS R24 US and Canada: forecast non convective shear, WS020/27055KT

The two most important rows are the first and the third. A METAR is a snapshot; a TAF is a story told in advance, with a beginning, an end, and chapters set out by change groups. The validity period page explains how the TAF period is written.

An example pair

An observation from the Aviation Weather Handbook for Pensacola:

METAR KPNS 030053Z 36005KT 10SM CLR 30/23 A2992 RMK AO2 SLP132

A forecast from NWS Instruction 10-813 for Casper:

TAF KCPR 110537Z 1106/1206 24015KT P6SM SKC

The two are from different airports and dates, but they show the format gap clearly. The METAR gives an observation time (0053 UTC on the 3rd), a temperature and dew point (30 and 23 degrees Celsius), an altimeter setting (29.92 inHg) and remarks. The TAF gives an issue time (0537 UTC on the 11th) followed by a validity period, from 0600 UTC on the 11th to 0600 UTC on the 12th, and nothing about temperature or pressure.

Codes that differ between the two

Most groups are written identically in both reports. A few are not, and the differences are a common source of confusion in the United States.

Clear sky. NWS Instruction 10-813 states that when zero oktas are forecast the cloud group is replaced by SKC, and that the contraction CLR, used in the METAR code, is not used in TAFs. In a US METAR, CLR comes from automated stations and means no layers detected at or below 12,000 feet, according to the Aviation Weather Handbook. The cloud codes page compares SKC, CLR, NSC and NCD.

Good visibility. A US METAR reports 10SM when visibility is 10 statute miles or more. A US TAF does not forecast beyond 6: the Aviation Weather Handbook states that visibility greater than 6 statute miles is encoded as P6SM. In ICAO reports, both use metres and 9999.

Vicinity. NWS Instruction 10-813 gives two definitions of VC. In NWS TAFs it means the ring between 5 and 10 statute miles from the centre of the runway complex. The WMO definition, within 8 km (5 statute miles) of the aerodrome but not at it, is noted in the instruction as used only in METARs and SPECIs.

Wind shear. The METAR WS group reports shear observed on a runway. The TAF WS group, used in the United States and Canada, forecasts non convective shear up to a given height. The low level wind shear page covers the forecast group.

Area covered

A METAR is a point observation, extended to the aerodrome. WMO-No. 782 notes that for automated systems a sufficient number of point measurements should be made within the area of interest and extrapolated as best as possible.

A TAF is an area forecast for the aerodrome. TC AIM states that TAFs are intended to relate to weather conditions within 5 nautical miles of the centre of the runway complex, depending on local terrain. WMO-No. 782 says weather phenomena are forecast for an area within a radius of approximately 8 km of the aerodrome reference point, and that cloud forecasts represent the aerodrome and its vicinity.

How a forecaster uses the METAR

The METAR is one input to the TAF, not its foundation alone. The Aviation Weather Handbook explains that a complete METAR is not needed for each TAF: forecasters use the "total observation concept", with nearby surface observations, radar, satellite, radiosonde data, models, aircraft reports and other sources.

Observations still matter for the forecast service. NWS Instruction 10-813 requires wind, visibility, sky condition, temperature, dew point and altimeter setting at a minimum before a new TAF location is approved. When observations are missing or incomplete, the forecaster appends AMD NOT SKED; when they are missing for more than a TAF cycle, the TAF may be suspended with NIL TAF. These codes are explained on the amended TAF page.

Using both together

The practical rule is to read the two as a pair.

  1. Read the latest METAR for the conditions now, including the elements a TAF lacks: temperature, dew point, altimeter setting, RVR.
  2. Find the current TAF for the same aerodrome, and the part of it that covers the present time.
  3. Compare. If the METAR matches the TAF period it falls in, the forecast is on track. If the METAR is much worse or much better, the forecast may soon be amended.
  4. Read the TAF forward for the arrival time, including TEMPO and PROB groups.

A SPECI between routine METARs signals a significant change in observed conditions, often the first sign that a TAF is off track. A METAR TREND, used in Europe and elsewhere, bridges the two: a two hour forecast attached to the observation.

Method and limits

The definitions, issue frequencies and code differences are quoted from WMO-No. 782 (2025 edition), NWS Instruction 10-813 (October 2024), the Aviation Weather Handbook and the Transport Canada AIM MET section. The KPNS and KCPR lines are examples printed in those documents, not a matched observation and forecast for the same place and time. Issue schedules vary by country and aerodrome; national publications such as the Canada Flight Supplement give local times. This page has no "In real reports" box because it compares two report types rather than a single group.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What is the main difference between a TAF and a METAR?

A METAR is a report of the weather actually observed at an aerodrome at a given time. A TAF is a forecast of the most probable conditions at the aerodrome over a validity period of up to 30 hours. One describes the present, the other the expected future.

How often are METARs and TAFs issued?

WMO-No. 782 states that a METAR is issued at hourly or half hourly intervals, with SPECI reports when criteria are met. It states that TAFs valid for 12 to 30 hours should be issued every 6 hours, and shorter TAFs every 3 hours, with amendments when needed.

Why does a TAF have no temperature or altimeter setting?

The standard TAF forecasts the elements that most affect take off and landing: wind, visibility, weather, cloud and, in US and Canadian TAFs, low level wind shear. Temperature appears only in the optional TX and TN groups, and a QNH forecast only in military style TAFs. The METAR carries the observed values.

If the METAR and the TAF disagree, which one is right?

The METAR describes the weather that is actually there. A forecast that no longer matches the observations may be amended: NWS Instruction 10-813 sets amendment criteria for ceiling, visibility, wind, weather and wind shear. Until an amendment arrives, the observation shows the real conditions.

Do a TAF and a METAR cover the same area?

Not exactly. A METAR describes the weather at the observing site and reports nearby weather with VC. TC AIM states that TAFs relate to conditions within 5 NM of the centre of the runway complex, and WMO-No. 782 places forecast weather within about 8 km of the aerodrome reference point.

Sources

  1. World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition
  2. National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024)
  3. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A), chapters 24 and 27
  4. Transport Canada (2025). TC AIM, MET section, aviation weather services and TAFs