The $ maintenance indicator and sensor status remarks in a METAR

Tafrob editorial team · Updated · 5 min read

Short answer

In an automated US METAR, a trailing dollar sign means the system detected that maintenance is needed. Sensor status remarks such as PWINO, PNO, FZRANO, TSNO, VISNO LOC and CHINO LOC mean an equipped sensor is not operating, and RVRNO means a runway visual range that should be reported is missing. They flag missing data, not weather.

Key points

  • The $ sign is the maintenance indicator: an automated system sets it when it detects that maintenance is needed.
  • PWINO, PNO, FZRANO, TSNO, VISNO LOC and CHINO LOC are coded only when the station is equipped with that sensor and it is not operating.
  • RVRNO is coded when runway visual range should be reported but is missing.
  • These remarks come from automated stations only; a manual observation does not carry them.
  • A sensor status remark tells you what the report cannot see, which matters when you read a report that shows no precipitation or no thunderstorm.
Visibility sensor of an Automated Surface Observing System mounted on a mast at an airport
Photo: Famartin, CC BY-SA 4.0, via Wikimedia Commons

What are sensor status indicators in a METAR?

Sensor status indicators are remarks that say an automated sensor is not working, so the report is missing data it would normally carry. They are not weather observations. They belong to what the Aviation Weather Handbook calls maintenance data groups, which are only reported from automated stations. For the wider remarks section, see METAR remarks (RMK).

The reason they exist is simple. An automated station reports what its sensors measure, and if a sensor fails, silence looks the same as "nothing happening". The status remark removes that ambiguity: it tells the reader that the absence of a phenomenon in the report is not evidence of its absence in the sky.

What are the sensor status remarks?

FMH-1 and the Aviation Weather Handbook list the same set. Each one except RVRNO applies only when the station is equipped with that sensor and the sensor is not operating.

Remark Meaning (FMH-1 glossary) Condition for coding
RVRNO RVR system not available Runway visual range should be reported but is missing
PWINO Precipitation identifier sensor not available Station has a present weather identifier and it is not operating
PNO Precipitation amount not available Station has a tipping bucket rain gauge and it is not operating
FZRANO Freezing rain sensor not available Station has a freezing rain sensor and it is not operating
TSNO Thunderstorm information not available Station has a lightning detection system and it is not operating
VISNO LOC Visibility at secondary location not available Station has a secondary visibility sensor and it is not operating
CHINO LOC Sky condition at secondary location not available Station has a secondary ceiling height indicator and it is not operating

In VISNO LOC and CHINO LOC, LOC stands for the location of the secondary sensor, written in place of the letters. The sources opened for this page show the format as VISNO_LOC and CHINO_LOC with a placeholder, and they do not give a worked example, so none is invented here. For the rules on runway visual range itself, see runway visual range.

What does the $ sign mean?

The dollar sign is the maintenance indicator. FMH-1 says a maintenance indicator sign, $, is coded when an automated system detects that maintenance is needed on the system. JO 7900.5E says the same in its paragraph 13.58, and phrases it as a sign included when an ASOS or AWOS-C detects that maintenance is needed. The FMH-1 glossary lists it as the maintenance check indicator.

What the sign does not say matters just as much:

  • It does not name the sensor or the fault.
  • It does not mean the reported values are wrong.
  • It does not mean the station is closed.

It is a flag for the people who maintain the system, and it is visible to everyone who reads the report. A pilot reading it should treat it as a reason to be careful with the data, not as a measurement. For the types of automated station, see AO1 and AO2.

Do these remarks appear on manual stations?

No. The Aviation Weather Handbook says the maintenance data groups, sensor status indicators and the maintenance indicator are only reported from automated stations. JO 7900.5E labels the maintenance indicator as an automated remark only. The same applies to the sensor status text in FMH-1, which is written for automated stations.

Combine that with the station-type remark. An AO2 or AO1 remark tells you the station is automated, and therefore that a sensor status remark can be present. In a manual or augmented report the observer covers the missing sensor, so there is nothing to flag in the same way.

How do you read a report with these remarks?

Two illustrative strings, built for this page to show the placement rather than copied from a source:

KXXX 181855Z AUTO 18012KT 10SM CLR 14/06 A3002 RMK AO2 SLP168 PWINO
KXXX 181855Z AUTO 18012KT 10SM CLR 14/06 A3002 RMK AO2 SLP168 TSNO $

The station identifier is a placeholder. Reading them:

  • PWINO (first string): the precipitation identifier is not working. The weather group is empty, so the report shows no precipitation, but the sensor that would have identified precipitation type is down. Check the nearby stations and the forecast before assuming dry weather.
  • TSNO and $ (second string): lightning information is not available and the system also flagged a need for maintenance. The report cannot be used to rule out thunderstorms. The order of the $ relative to other remarks is not shown in the sources opened for this page, so do not rely on the position in these examples.

A related code, UP for unknown precipitation, is covered on the UP page. It is a weather group entry from an automated station, which is different from a status remark about a sensor, though both come from the limits of automation.

What should a reader do when one appears?

Treat each remark as a limit on the report. These steps follow directly from the definitions above:

  1. Identify what the sensor measures: precipitation type (PWINO), precipitation amount (PNO), freezing rain (FZRANO), lightning (TSNO), runway visual range (RVRNO), secondary visibility (VISNO LOC) or secondary sky condition (CHINO LOC).
  2. Read the weather group knowing that phenomenon may be going unreported.
  3. Look for another source, such as a nearby station, the forecast or ATIS, before concluding the phenomenon is absent.
  4. If you see $, note that the system itself asks for maintenance, and give less weight to fine detail.

For the structure of the weather group that a failed sensor leaves incomplete, see the present weather group.

Common mistakes

  • Reading a sensor status remark as a weather phenomenon. They describe equipment, not the sky.
  • Assuming $ means a specific sensor is broken. FMH-1 only says maintenance is needed on the system.
  • Expecting these remarks from manual stations. They are only reported from automated stations.
  • Assuming NO at the end of a remark always means a failed sensor. SLPNO, for example, means sea level pressure is not available, which is a different case; see the SLP page.

This page is educational and is not a source for operational weather. For the complete report layout, see how to read a METAR.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does the $ at the end of a METAR mean?

The dollar sign is the maintenance indicator. FMH-1 says it is coded when an automated system detects that maintenance is needed on the system. FMH-1's glossary calls it the maintenance check indicator. It does not say which sensor is affected, and it does not mean the weather values in the report are wrong.

What does PWINO mean?

PWINO means the precipitation identifier is not available. It is coded when an automated station is equipped with a present weather identifier and that sensor is not operating. Because the sensor cannot report the type of precipitation, the weather group in that report may be missing something that was actually occurring.

What does TSNO mean in a METAR?

TSNO means thunderstorm information is not available. It is coded when an automated station is equipped with a lightning detection system and that sensor is not working. The report then cannot be relied on to show thunderstorms, so the absence of TS in the weather group is not proof that none were occurring.

Do manual stations report PWINO or the $ sign?

No. The Aviation Weather Handbook states that the maintenance data groups, the sensor status indicators and the maintenance indicator are only reported from automated stations. A manual station has an observer who can assess weather directly, so these remarks apply only where a sensor or automated system does the observing.

Sources

  1. Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1 (FCM-H1-2019)
  2. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
  3. Federal Aviation Administration (2021). Order JO 7900.5E, Surface Weather Observing, Change 1