Runway visual range (RVR) in a METAR: how to decode R27L/1100U

Tafrob editorial team · Updated · 5 min read

Short answer

RVR is an instrument-derived distance a pilot may see down a runway. In ICAO reports R27L/1100U means runway 27 left, 1100 meters, tending upward over the previous 10 minutes. US reports use feet, as in R17L/2600FT. P means above the highest reportable value and M means below the lowest. It appears only in low visibility.

Key points

  • RVR is measured by instruments along a specific runway, so it can differ from the prevailing visibility in the same report.
  • The ICAO group is R, runway designator, a slash and four digits in meters; the US group ends in FT.
  • P before the value means more than the highest reportable value; M means less than the lowest.
  • ICAO tendency letters U, D and N describe the last 10 minutes; US reports show variability with V instead.
  • The group is absent when conditions are good, so a missing RVR usually means visibility is not low.
Runway visual range sensor posts on a gravel pad beside an airfield
Photo: Aeronautical & General Instruments Limited, CC BY-SA 3.0, via Wikimedia Commons

What is runway visual range?

FMH-1 describes RVR as an instrument-derived value representing the horizontal distance a pilot may see down the runway. It is measured by a sensor beside the runway, usually a transmissometer or a forward scatter meter, not estimated by an observer looking at landmarks. That makes it a better guide to what a crew will see on a specific runway than the airport-wide prevailing visibility.

Where the sensor sits matters. FMH-1 places RVR sensors within 500 ft of the runway centerline and within 1,000 ft of the threshold. The Aviation Weather Handbook says the values reported come from the touchdown zone, and that when several runways are in use the operating runway with the lowest touchdown RVR is reported. CAP 746 and WMO-No. 782 also describe touchdown zone values, for up to four runways.

When does a METAR include RVR?

RVR is a low-visibility group, so most METARs have none.

System Reporting condition Source
United States Prevailing visibility is 1 SM or less, and/or the RVR for the designated instrument runway is 6,000 ft or less FMH-1
United Kingdom The minimum visibility or the RVR is below 1500 m CAP 746
Canada Prevailing visibility is 1 mile or less and/or RVR is 6,000 ft or less NAV CANADA

For the US, the Aviation Weather Handbook also lists RVR as a special report (SPECI) trigger: the highest value from the designated RVR runway decreases to less than 2,400 ft in the preceding 10 minutes, or, if it is below 2,400 ft, increases to equal or exceed 2,400 ft.

If a station should report RVR but the value is missing, FMH-1 says RVRNO is coded, and its list of abbreviations gives RVRNO as RVR system not available. See maintenance indicator and sensor status.

How is the ICAO RVR group built?

WMO-No. 782 gives the format as RDRDR/VRVRVRVRi: the letter R, the runway designator, a slash, four digits in meters, and an optional tendency letter.

Part Example Meaning
R R Runway
Designator 27L Runway 27 left; a letter separates parallel runways
Slash / Separator
Value 1100 RVR in meters
Tendency U Optional trend over the last 10 minutes

The reportable steps, from WMO-No. 782 and CAP 746, are 25 m below 400 m, 50 m from 400 m to 800 m and 100 m above 800 m, with values rounded down. The value is a 10-minute mean. Examples from CAP 746 include R04/0075, R27L/0650, R16R/1100 and R12/1100U.

Tendency has a precise definition in CAP 746: a difference of 100 m or more between the mean of the first 5 minutes and the mean of the second 5 minutes of the 10-minute period. The letters are U (increased), D (decreased) and N (no distinct change). WMO-No. 782 says tendency is omitted when it cannot be determined, and that missing RVR is coded R24/////.

What do the P and M prefixes mean?

Both systems cap the scale at each end, and the prefixes tell you the real value is outside it.

Prefix Meaning ICAO example US example
P Above the highest reportable value R24/P2000 (WMO-No. 782) R27/P6000FT (FMH-1)
M Below the lowest reportable value R24/M0150 (WMO-No. 782) R01L/M0600FT (FMH-1)

CAP 746 gives R33/M0050 and R24L/P1500 as UK examples, and notes that the highest value may be less than 2000 m because of equipment limits. So P always refers to that particular system, not to a fixed number.

How does the US format differ?

FMH-1 gives the US group as RDRDR/VRVRVRVRFT, for example R01L/0800FT, with values in feet. Reportable increments are 100 ft up to 1,000 ft, 200 ft from 1,000 to 3,000 ft and 500 ft from 3,000 to 6,000 ft. Manual stations do not report RVR below 600 ft and report only the designated runway; automated stations may report up to four designated runways.

When RVR is changing, the US group shows a range with a V between the two values. FMH-1 gives R01L/0600V1000FT. It also says a single value is reported if the 10-minute high and low are the same, and manual RVR is based on light setting 5.

Canada adds tendency letters to the feet format. NAV CANADA shows R33/4000FT/D, with U, D or N after a slash. It reports a 10-minute mean touchdown-zone value, and when RVR varies significantly a one-minute maximum or minimum value is prefixed with V. NAV CANADA also uses RVR MISG for missing RVR data.

Decoding real examples

US example from the Aviation Weather Handbook:

METAR KOKC 011955Z AUTO 22015G25KT 180V250 3/4SM R17L/2600FT +TSRA BR OVC010CB 18/16 A2992
  • 3/4SM: prevailing visibility three quarters of a statute mile, which is below the 1 SM threshold, so RVR appears.
  • R17L/2600FT: runway 17 left, RVR 2,600 ft.
  • +TSRA BR: heavy thunderstorm with rain and mist, the cause of the low values.

ICAO example from WMO-No. 782:

SPECI LUDO 211025Z 31015G27KT 280V350 4000 1400SW R24/P2000 +SHRA FEW005 FEW010CB SCT018 BKN025
  • 4000 1400SW: prevailing 4 km, minimum 1.4 km southwest.
  • R24/P2000: runway 24, RVR above the highest reportable value of 2000 m.

UK-style multiple runways, from CAP 746:

R24L/P1500 R24R/1100
  • Runway 24 left is above 1500 m, and runway 24 right is 1100 m. Each runway gets its own group.

Canadian example from NAV CANADA:

METAR CYXE 292000Z CCA 30015G25KT 3/4SM R33/4000FT/D -RA BR BKN008 OVC040 21/19 A2992
  • R33/4000FT/D: runway 33, 4,000 ft, decreasing.

Common mistakes

  • Reading R17L as a heading. It is the runway designator.
  • Assuming P or M show an exact value. They mark the edge of the reportable scale.
  • Reading U, D and N in a US METAR. They belong to ICAO and Canadian formats.
  • Treating a missing group as a fault. It usually means conditions are above the thresholds, so check the visibility group and the weather group before assuming a sensor problem.
  • Reading RVR as a promise of what you will see. It is an instrument value for one runway, taken at a sensor position, and the weather can change quickly.
  • Mixing feet and meters. Check the unit before comparing; see units in METAR by country.

This page is educational and is not a source for operational weather. For the wider picture, see how to read a METAR and US versus ICAO differences.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

Why is there no RVR in most METARs?

RVR is reported only in low visibility. In the US, FMH-1 requires it when prevailing visibility is one mile or less or the designated runway RVR is 6,000 ft or less. CAP 746 reports it in the UK when the minimum visibility or the RVR is below 1500 m.

What do P and M mean in front of an RVR value?

P means the value is above the highest the system reports, for example R27/P6000FT in the US or R24/P2000 in WMO examples. M means below the lowest reportable value, for example R01L/M0600FT or R24/M0150. Neither is a measured figure.

What do the letters U, D and N at the end mean?

In ICAO reports they give the tendency over the previous 10 minutes: U for increasing, D for decreasing and N for no distinct change. WMO-No. 782 says the letter is omitted when tendency cannot be determined. US METARs do not use these letters.

Is RVR the same as visibility?

No. Visibility is the prevailing value across the horizon, while RVR is an instrument-derived value along a runway. FMH-1 defines RVR as the horizontal distance a pilot may see down the runway. The two can differ in the same report.

Sources

  1. Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1 (FCM-H1-2019)
  2. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
  3. World Meteorological Organization (2025). Aerodrome Reports and Forecasts, A Users' Handbook to the Codes (WMO-No. 782)
  4. UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
  5. NAV CANADA. Aviation Weather Services Guide