SLP in a METAR: how to decode sea level pressure
SLP is the sea level pressure remark in a US METAR. SLP is followed by three digits in tenths of a hectopascal, with the leading hundreds and thousands digits dropped: SLP982 is 998.2 hPa and SLP132 is 1013.2 hPa. SLPNO means the value is not available. It is a separate value from the altimeter setting in the A group.
Key points
- SLPppp gives sea level pressure in tenths of hPa; the first digits (hundreds and thousands) are not coded and must be inferred.
- Handbook examples: SLP982 means 998.2 hPa and SLP132 means 1013.2 hPa.
- SLPNO is coded when sea level pressure is not available.
- SLP lives in the remarks and is a different parameter from the altimeter setting (A2992), which is in the body.
- SLP is computed from station pressure, station elevation and a 12-hour mean temperature, so it is a derived value.

What is SLP in a METAR?
SLP is the sea level pressure remark that US stations add after RMK. It is the station's atmospheric pressure converted to what it would read at mean sea level, and it is written as the letters SLP followed by three digits. It exists for meteorology, such as drawing surface pressure maps, rather than for setting an altimeter. For the full layout of the remarks section, see METAR remarks (RMK).
The Aviation Weather Handbook gives the format for designated stations: the identifier SLP, immediately followed by the sea level pressure in millibars, with the hundreds and thousands units not coded. Those missing digits "must be inferred". A millibar and a hectopascal are the same size, so the Handbook figures in millibars read directly as hectopascals.
How do you decode the three digits?
The three digits are tens, units and tenths of a hectopascal, so a decimal point goes before the last digit. The reader then restores the two digits that were dropped. The Handbook gives two worked values:
| Remark | Digits read as | Sea level pressure |
|---|---|---|
| SLP982 | 98.2 | 998.2 hPa |
| SLP132 | 13.2 | 1013.2 hPa |
The step that trips people up is the prefix. For 982 the missing digits are "9" and for 132 they are "10", and nothing in the remark itself says which. The Handbook states only that they are inferred. In practice the reader chooses the prefix that gives a plausible sea level pressure, which is why the same logic works for a deep low and a strong high. No numeric threshold for the choice appears in the handbooks used for this page, so none is given here. A decoder that handles this should use the altimeter setting in the body as a cross-check, as shown further down.
What is an example of SLP in a full METAR?
The Aviation Weather Handbook decodes this report:
KPNS 030053Z 36005KT 10SM CLR 30/23 A2992 RMK AO2 SLP132 T03000233
- A2992: altimeter setting of 29.92 inHg, in the body. See QNH and altimeter setting.
- RMK AO2: the remarks start, and the station is an automated station with a precipitation discriminator. See AO1 and AO2.
- SLP132: sea level pressure of 1013.2 mb.
- T03000233: hourly temperature 30.0 C and dew point 23.3 C. See the T group.
The Handbook decodes the altimeter as 29.92 inHg (1013.3 mb) and the sea level pressure as 1013.2 mb. The two numbers are close but not identical, and that is expected, as the next section explains.
SLP versus the altimeter setting
SLP and the altimeter setting answer different questions, and they are computed differently. The altimeter setting is the value a pilot sets in the Kollsman window so that the altimeter reads field elevation on the ground. It sits in the body of the report in the A group, in hundredths of an inch of mercury. SLP is a remark in tenths of a hectopascal.
FMH-1 describes how SLP is built. It is computed by adjusting station pressure to compensate for the difference between the station elevation and sea level, and the adjustment is based on the station elevation and the 12-hour mean temperature at the station. The 12-hour mean is the average of the present ambient temperature and the ambient temperature 12 hours ago. Stations within 50 feet of sea level may be authorized by their agency to use a constant value for the adjustment.
FMH-1 also says the altimeter setting is rounded down to the next reportable value, which is a further reason the two figures rarely match exactly.
| Altimeter setting | SLP | |
|---|---|---|
| Where in the report | Body (A group) | Remarks (after RMK) |
| Unit | Inches of mercury, hundredths | Hectopascals, tenths |
| Purpose | Setting the altimeter | Meteorological analysis |
| Example from the handbook | A2992 | SLP132 |
To convert between hectopascals and inches of mercury, use the pressure converter. Do not use SLP as a substitute for the altimeter setting in an altimeter, because it is a different number built for a different job.
What does SLPNO mean?
SLPNO means sea level pressure is not available. The Aviation Weather Handbook states that for a METAR, if sea level pressure is not available, it is coded SLPNO. JO 7900.5E lists the same remark in its table of remarks elements for the sea level pressure paragraph. The code replaces the three digits entirely.
METAR KJFK 181851Z 24010KT 10SM FEW250 12/04 A3010 RMK AO2 SLPNO
This string is an illustration built for this page, not a copy of a real report. It shows only the shape of the remark: the letters SLP followed by NO in the place where the digits would be.
Seeing SLPNO tells you the pressure is missing. It does not tell you why, and it does not mean the altimeter setting in the body is wrong. Those are independent values.
Which reports carry SLP?
SLP is a remark at designated stations. FMH-1 says sea level pressure is included in the remarks of all METARs at designated stations, and the Handbook phrases the rule the same way ("at designated stations"). That is the reason the frequency box on this page reflects only a share of all reports: stations that are not designated, and non-US reports, do not carry it.
The remark is a US practice defined in the US handbooks cited here. For other countries, check that country's own rules before assuming the same group is present. The site's US versus ICAO METAR differences page covers where national remarks diverge.
The remark order matters when you read a long RMK section. In the Handbook's remarks table, sea level pressure is item 22, and the additive groups such as precipitation, temperature extremes and pressure tendency follow it. That is why SLP usually sits right before the T group and the other additive data, which are explained on the additive data groups page.
What is the 3-hourly pressure tendency next to SLP?
On 3-hourly reports a different group, 5appp, describes how the pressure changed in the past three hours. In the format 5appp, 5 is the group indicator, a is the character of the pressure change and ppp is the amount in tenths of hectopascals. FMH-1 gives "52032" as a steady increase of 3.2 hectopascals in three hours. JO 7900.5E repeats the same example, and says the amount is based on the absolute value of the change of either station pressure or altimeter setting over the past 3 hours. Full coverage of that group, with its table of characteristics, is on the additive data groups page.
Common mistakes
- Reading SLP132 as 132 hPa or as 13.2 hPa. The missing leading digits must be added back.
- Treating SLP as the altimeter setting. Set the altimeter from the A group or from ATC, never from a remark.
- Assuming SLPNO means a bad altimeter value. It reports only that sea level pressure is missing.
- Expecting SLP in every report. It is a designated-station remark and it is not in every METAR.
This page is educational and is not a source for operational weather. For the whole report structure, see how to read a METAR.
Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).
Frequently asked questions
What does SLP132 mean in a METAR?
SLP132 is a sea level pressure of 1013.2 hPa. The Aviation Weather Handbook gives exactly this example: the hundreds and thousands digits are not coded and must be inferred, so the three digits 132 are read as 13.2 and prefixed to give 1,013.2 mb. It is not the altimeter setting.
What does SLPNO mean?
SLPNO means sea level pressure is not available. The Aviation Weather Handbook says that for a METAR, if sea level pressure is not available, it is coded SLPNO. It is a missing-data flag in the remarks, like other NO remarks, and it does not by itself say why the value is missing.
Is SLP the same as the altimeter setting?
No. The altimeter setting (A2992) is in the body, in inches of mercury, and is what pilots set on the altimeter. SLP is a remark in hectopascals computed with a 12-hour mean temperature. In the Handbook example, altimeter 29.92 inHg corresponds to 1013.3 mb while SLP reads 1013.2 mb.
Why does my METAR have no SLP?
FMH-1 requires SLP at designated stations, so a METAR without the remark usually comes from a station that does not report it, and a station that should report it but cannot codes SLPNO. Not every station is a designated station, so check the remarks of the station you are reading.
Sources
- Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1 (FCM-H1-2019)
- Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
- Federal Aviation Administration (2021). Order JO 7900.5E, Surface Weather Observing, Change 1