BECMG in a TAF: the gradual change group explained

Tafrob editorial team · Updated · 6 min read

Short answer

BECMG means becoming. It is followed by a start and an end time in whole UTC hours, and it describes conditions that reach or pass stated values at a regular or irregular rate at some unspecified time inside that period. The period must not exceed 4 hours. After the period, the new conditions continue as the prevailing ones.

Key points

  • BECMG is followed by a period such as 2808/2809, in whole hours UTC, and the period must not exceed 4 hours.
  • The change happens at an unspecified time inside the period, so the exact moment is not forecast.
  • Only elements with a significant change are written, but a significant cloud change needs all cloud groups.
  • NWS TAFs do not use BECMG; ICAO, EU and Canadian TAFs do.
A red sunrise over the apron and terminal buildings at Schiphol Airport in Amsterdam
Photo: Rab Lawrence, CC BY 2.0, via Wikimedia Commons

What BECMG means

BECMG is short for becoming. It marks a change of conditions that does not happen at one precise moment. The EU rules in Regulation (EU) 2017/373 define it as a group used when conditions are expected to reach or pass specified thresholds at a regular or irregular rate, at an unspecified time during the period. The Met Office GetMet leaflet reads the same group as "Becoming".

Two features set it apart from the other change groups. It carries a period with a start and an end, and it does not say when inside that period the change happens. A BECMG is also permanent: after the period ends, the new conditions are simply the prevailing ones, and they continue until another change group changes them. The pillar page on reading a TAF shows where this group sits in the order of a full forecast.

The time period

BECMG is followed by two time values written as DDHH/DDHH, in whole hours UTC, such as BECMG 1618/1620. The EU text states that BECMG or TEMPO is followed by a period in whole hours UTC, and that for BECMG the period must not exceed 4 hours.

Transport Canada gives the typical duration. A BECMG change is normally 1 to 2 hours and not more than 4. Canada also asks that BECMG be kept to a minimum: use it for at most 2 groups changing, and otherwise prefer FM.

The day digits and the 24 hour convention follow the same rules as the validity group, which are explained in TAF validity period.

Which time is meant: start or end

Since the exact time of the change is not forecast, a reader has to decide what to assume. Transport Canada gives a rule for planning with IFR alternates: improving conditions are considered to apply at the end of the change period, and deteriorating conditions at the start. The rule is intended for alternate planning, not as a statement of when the weather will change.

Its example shows how it works. BECMG 2808/2809 OVC030 means a change to overcast at 3,000 feet AGL between 0800Z and 0900Z on the 28th. If the sky before was better than OVC030, the change applies from 0800Z, because conditions are getting worse. If it was worse, the change applies from 0900Z, because conditions are improving.

What to write after BECMG

The EU rules say that only elements with a significant change are included after BECMG or TEMPO, with one exception: when a significant change in cloud is forecast, all cloud groups are indicated. Transport Canada has a related rule. Only the changed elements follow BECMG, but when there is a significant change in weather or visibility, all weather groups and the visibility are repeated.

This is a difference from FM, where the whole forecast is restated. It means that after a BECMG you must carry forward whatever the group does not mention. The FM rule is on the FM group page.

Sourced examples

The first two examples come from the EU template in Regulation (EU) 2017/373 and show only the change group.

Group Source reading
BECMG 1618/1620 8000 NSW NSC Visibility changing to 8000 m, with no significant weather and no significant cloud
BECMG 3010/3011 00000MPS 2400 OVC010 Wind calm, visibility 2400 m, overcast at 1000 ft
BECMG 1412/1414 RA Rain beginning

The Met Office GetMet leaflet gives two complete forecasts that use BECMG. The first is a 24 hour TAF issued at 0500 UTC on the 11th, valid from 06 on the 11th to 12 on the 12th:

EGPK 110500Z 1106/1212 13010KT 9999 BKN010 BECMG 1106/1108 BKN018
PROB30 TEMPO 1108/1116 17025G40KT 4000 TSRA BKN012CB
BECMG 1118/1121 3000 BR NSC=

The first BECMG lifts the cloud base to 1,800 feet between 0600 and 0800 UTC on the 11th. The second BECMG, from 1800 to 2100 UTC, brings the visibility down to 3000 m in mist with no significant cloud. The line is split in three here for reading; the leaflet prints it as one line.

The second is a 9 hour TAF issued at 0800 UTC on the 30th, valid 0900 to 1800:

EGTE 300800Z 3009/3018 23010KT 9999 SCT010 BKN018 BECMG 3011/3014
6000 -RA BKN012 TEMPO 3014/3018 2000 DZ OVC004 =

Here the BECMG spans three hours, from 1100 to 1400 UTC, with visibility reducing to 6000 m in light rain and the cloud changing to a 1,200 foot broken layer. The cloud group is written in full because cloud changed. After 1400 UTC those conditions are the prevailing ones, and the TEMPO that follows applies to them. For the TEMPO group see TEMPO.

Transport Canada's sample is another sourced case. TAF CYVP 301213Z 3012/3024 VRB03KT 1/4SM -RA FG BKN003 OVC007 is followed by BECMG 3012/3014 4SM -DZ BR OVC007. The change moves the visibility to 4 statute miles with light drizzle and mist over the first two hours of the forecast, and the overcast layer is repeated.

The US position

NWS Instruction 10-813 lists BECMG among the international groups that NWS TAFs do not use. A US forecaster makes a gradual change with FM, TEMPO or PROB30 instead, depending on its timing and probability. If you only read US TAFs, you will rarely see BECMG at all.

There is one point of caution. The FAA Aeronautical Information Manual sample TAF for KPIT ends with BECMG 1013/1015 P6SM NSW SKC even though the AIM says NWS does not use BECMG. The sample illustrates the code rather than NWS practice, so it should not be taken as proof that US forecasters write the group. The meaning of NSW in that line is on the NSW page.

BECMG compared with TEMPO and FM

Group Nature of change Duration rule in the sources
BECMG Permanent, gradual, at an unspecified time in the period Period must not exceed 4 hours (EU), normally 1 to 2 hours (Canada)
TEMPO Temporary fluctuation Under 1 hour each time and under half the period in aggregate (EU)
FM Rapid and permanent Starts at one stated time

The EU rule also tells the forecaster which group to use when a TEMPO fluctuation would last 1 hour or longer: use BECMG, or subdivide the period with FM. The comparison page works through this choice.

Common mistakes

  • Reading BECMG as a change at the start time. The change can happen anywhere in the period.
  • Forgetting that the change is permanent. After the period, the new conditions stay in force.
  • Dropping cloud layers that were not rewritten. When cloud changes, all cloud groups are indicated, but when it does not, the old layers still apply.
  • Expecting BECMG in a US TAF. NWS does not use it.
  • Mixing up TREND and TAF. The EU rules also use BECMG and TEMPO in the TREND forecast attached to a METAR, with FM, TL and AT as time indicators, and a validity of 2 hours. That is covered in TREND and NOSIG.

You can run any of the lines above through the TAF decoder.

Method and limits

The rules on this page come from Regulation (EU) 2017/373, the Transport Canada AIM MET section, NWS Instruction 10-813, the Met Office GetMet leaflet and the FAA Aeronautical Information Manual. The line breaks in the Met Office example are added for reading, and the readings of the table rows are a plain language decoding of the EU template.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does BECMG mean in a TAF?

BECMG means becoming. It introduces a gradual change to new conditions during a stated period in whole UTC hours, for example BECMG 1618/1620 8000 NSW NSC from the EU template. Once the period ends, the new conditions are the prevailing ones until another change group says otherwise.

How long can a BECMG period be?

Regulation (EU) 2017/373 says the BECMG period must not exceed 4 hours. Transport Canada describes a normal change of 1 to 2 hours and not more than 4. Canada also asks forecasters to keep BECMG to a minimum, using it for at most 2 groups changing and otherwise preferring FM.

Which time in a BECMG applies, the start or the end?

The change happens at an unspecified time inside the period, so the TAF does not say. Transport Canada gives a planning rule for IFR alternate decisions: improving conditions are taken to apply at the end of the change period, and deteriorating conditions are taken to apply at its start.

Why do US TAFs not contain BECMG?

NWS Instruction 10-813 lists BECMG among the international groups that NWS does not use, and its change group guidance is built on FM, TEMPO and PROB30 instead. The FAA AIM sample TAF still shows a BECMG line because it illustrates the code, so you can meet it in training material.

Sources

  1. European Union (EUR-Lex) (2017). Commission Implementing Regulation (EU) 2017/373, Annex V (Part-MET), aerodrome forecasts and TAF template
  2. Transport Canada (2025). TC AIM, MET section 7.0 Aerodrome forecasts (TAFs)
  3. National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024)
  4. Met Office. GetMet: aerodrome forecast TAF decode
  5. Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1