Wind shear in a METAR: reading WS R24 and WS ALL RWY

Tafrob editorial team · Updated · 5 min read

Short answer

The wind shear group is an optional supplementary group of the ICAO METAR. WS followed by a runway designator, such as WS R24, says wind shear was reported in the take-off or landing zone of that runway. WS ALL RWY covers every runway. It concerns the lowest 500 m (1,600 ft) and is used only where local circumstances warrant.

Key points

  • WS R24 means wind shear significant to aircraft was reported along the take-off or approach path of runway 24; WS ALL RWY means all runways.
  • WMO-No. 782 defines the layer as the lowest 500 m (1,600 ft) and says the group is reported where local circumstances warrant, so many METARs never carry it.
  • The group belongs to the supplementary section, after recent weather and before any sea-surface group.
  • CAP 746 states that wind shear groups are not reported in the United Kingdom, so the absence of WS there says nothing about the air.
  • NAV CANADA writes the group as WS RWY33, covers 1,500 ft AGL and below, and adds it when an aircraft reports shear.
Terminal Doppler weather radar station near an airport in Colorado
Photo: Greg Goebel from Loveland CO, USA, CC BY-SA 2.0, via Wikimedia Commons

What is the wind shear group?

The wind shear group is one of the optional elements at the end of the ICAO METAR. It tells a crew that wind shear significant to aircraft operations was reported along the take-off or approach path. It is short, a few characters after the pressure and recent weather groups, and it is rare. The frequency box on this page shows how often it appears in the dataset behind this site. For the full order of groups in a report, see how to read a METAR.

WMO-No. 782 places the group in section 9, supplementary information. That section is used, in its words, for recent weather phenomena of operational significance, information on wind shear in the lower layers, and sea-surface temperature and state of the sea. It adds that these optional elements are included in METAR and SPECI in accordance with ICAO regional air navigation agreement. So the group exists in the code, but whether a given aerodrome ever uses it is a local and regional decision.

Format: WS RDRDR and WS ALL RWY

WMO-No. 782 shows two forms:

Group Meaning
WS RDRDR Wind shear on one runway, where DRDR is the runway designator
WS ALL RWY Wind shear affecting all runways

The handbook gives the example WS R24 and explains it as wind shear reported in either the take-off or the landing zone of runway 24. It also says the information should be given where local circumstances warrant, and that it applies to wind shear significant to aircraft operations along the take-off or approach paths in the lowest 500 m (1,600 ft).

Three details follow from that wording.

  • The layer is the lowest 500 m (1,600 ft), so the group is about the approach and the departure, not about shear at cruise levels.
  • The group says nothing about strength, direction or type. It flags that shear was reported, and the crew must look elsewhere for details.
  • The runway designator uses the same runway naming as the runway visual range group, so R24 reads the same way in both.

Where does it sit in the report?

The WMO-No. 782 code table lists the supplementary groups in this order: recent weather, wind shear, then sea-surface temperature and state of the sea. Its own running example shows them together:

RERA WS R24 W19/S4

This line is the end of the WMO handbook example. RERA is recent rain, WS R24 is the wind shear group for runway 24, and W19/S4 is the sea-surface group, which has nothing to do with the runway. The recent weather group is covered on the recent weather page. All of this comes before the trend forecast and before any remarks.

What happens in the UK and the US?

The answer depends on where you read the report.

United Kingdom. CAP 746 lists the variations in UK coding compared with the full WMO table. One of them states that wind shear groups are not reported in the United Kingdom. A UK METAR with no WS group therefore tells you nothing about shear.

United States. Neither FMH-1 nor FAA Order JO 7900.5E has a wind shear group in the METAR body. The US reaches pilots with wind shear information through other products. The Aviation Weather Handbook says low-level wind shear and microburst information is included in the ATIS broadcast for 20 minutes following the last report, and that AIRMET Tango is issued when non-convective low-level wind shear potential below 2,000 ft AGL is occurring or expected. See the ATIS page and the PIREP page for the channels that carry such information.

The cited documents do not say how remarks are used for shear at US stations, so no US remark format is described here. The general structure of the remarks section is on the METAR remarks page.

The Canadian form: WS RWY33

The NAV CANADA Aviation Weather Services Guide decodes a sample METAR that contains the group WS RWY33, placed after the altimeter setting and before RMK:

A2992 WS RWY33 RMK SF5NS3 VIS NW 3/8 SLP134 DENSITY ALTITUDE 2500FT

The guide explains it as wind shear reported in the take-off or landing path of runway 33 at 1,500 ft AGL and below. It adds that wind shear information at 1,500 ft AGL and below is provided when reported by an aircraft, usually on take-off or landing. Two differences from the ICAO format stand out:

  • The Canadian text uses RWY and the number, written WS RWY33, where WMO-No. 782 writes WS R24.
  • The layer is 1,500 ft AGL and below, in feet, while the ICAO text uses 500 m (1,600 ft).

The trigger also differs. In the Canadian description the group depends on an aircraft report, so a pilot must have flown through the shear and reported it. That is a useful reminder when you read a clean METAR: nobody may have flown the approach yet.

Reading a WS group in practice

A WS group is a warning flag, so treat it as one.

  1. Note which runway is named. WS R24 does not apply to runway 06 at the same aerodrome unless WS ALL RWY or a second group says so.
  2. Check the surface wind group for gusts or a strong change, covered on the gusts page. Gusty wind and shear can appear in the same weather situation, though the group itself does not state a cause.
  3. Check the weather and clouds. Thunderstorms in the report are a common setting for low-level shear, and the TS page explains the code.
  4. Look at the forecast. The TAF can carry its own wind shear group, explained on the low-level wind shear in TAF page.
  5. Listen to the ATIS and any controller advisory before the approach.

Common mistakes

  • Reading WS R24 as a measured value. It is a yes or no flag for a runway.
  • Assuming a METAR without WS is free of shear. The group is optional, absent from UK reports, and in Canada tied to aircraft reports.
  • Mixing up the ICAO and Canadian spellings. WS R24 and WS RWY33 are the same kind of group, but the layers are stated differently.
  • Confusing the group with the recent weather group, which comes first and uses RE, and with the sea-surface group that can follow.

This page is educational and is not a source for operational weather.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does WS R24 mean in a METAR?

WS R24 is the ICAO wind shear group for runway 24. WMO-No. 782 explains that it means wind shear has been reported in either the take-off or the landing zone of that runway, within the lowest 500 m (1,600 ft). It is a report of shear, not a measurement of its strength.

What is the difference between WS R24 and WS ALL RWY?

WS followed by a runway designator limits the report to one runway. WS ALL RWY, from the same WMO-No. 782 format, says wind shear affects all runways at the aerodrome. Read the runway named in the group and do not assume it applies to the other runways.

Why does my METAR never show a WS group?

The group is optional. WMO-No. 782 says it is included where local circumstances warrant, and CAP 746 states that wind shear groups are not reported in the United Kingdom. FMH-1 and JO 7900.5E have no WS group in the US METAR body either.

Does the absence of WS mean there is no wind shear?

No. Wind shear can exist without being reported, because the group depends on local arrangements and, in the NAV CANADA description, on an aircraft actually reporting it. Check the ATIS, PIREPs and the TAF as well, never one group alone.

Sources

  1. World Meteorological Organization (2025). Aerodrome Reports and Forecasts, A Users' Handbook to the Codes (WMO-No. 782)
  2. UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
  3. NAV CANADA. Aviation Weather Services Guide
  4. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
  5. Federal Aviation Administration (2020). Order JO 7900.5E, Surface Weather Observing