ATIS: what the airport information broadcast says and how to use it

Tafrob editorial team · Updated · 5 min read

Short answer

ATIS is a continuous recorded broadcast of routine airport information: wind, visibility, sky condition, temperature, dew point, altimeter, runways and approaches in use, and notices. Each version has an identifying letter. Pilots listen before contacting the controller and then state the letter, for example information Sierra received.

Key points

  • ATIS is a recorded loop, updated when the official weather changes or the runway or approach changes.
  • Each recording carries a phonetic letter, from Alpha to Zulu, and the pilot reports it on first contact.
  • In the United States, sky condition, visibility and obstructions may be left out when the ceiling is above 5,000 feet and visibility is more than 5 miles.
  • 'Have numbers' means only wind, runway and altimeter and does not tell ATC that the ATIS was received.
  • An ATIS adds operational items a METAR does not carry, such as the runway and approach in use.
  • In the United Kingdom, wind shear and temperature inversion warnings can be broadcast on the ATIS.
Air traffic control tower at Edinburgh Airport
Photo: CAPTAIN RAJU, CC0, via Wikimedia Commons

What ATIS is

ATIS, the Automatic Terminal Information Service, is a continuous broadcast of recorded noncontrol information in high activity terminal areas. According to the AIM (section 4-1-13), it runs on a discrete VHF frequency or on the voice portion of a navigational aid. Its purpose is to lift routine information out of the radio traffic so that controllers do not repeat it to every aircraft. Airports that have an ATIS are shown in the Chart Supplement.

What the broadcast contains

The AIM lists the content in a set order:

  1. airport name and the phonetic information letter;
  2. time of the latest weather sequence, in UTC;
  3. wind, visibility, obstructions to vision, present weather and sky condition;
  4. temperature, dew point and altimeter setting;
  5. density altitude advisory when appropriate;
  6. remarks, then the approach and runway in use.

JO 7110.65 chapter 2, section 9 adds items that can be included: lightning, cumulonimbus and towering cumulus remarks, the magnetic wind from the automated system, runway condition codes with the time of the report, shortened runway warnings, low-level wind shear or microburst alerts, bird activity and taxiway closures. It also allows pertinent pilot reports in the broadcast.

The weather part follows the latest observation, so the METAR guide helps for the terms. The altimeter figure is explained on the altimeter setting page.

The shortened weather

The AIM allows a shorter report when the weather is good. Sky condition, visibility and obstructions to vision may be omitted when the ceiling is above 5,000 feet and the visibility is more than 5 miles, a situation controllers sometimes call "the weather is better than 5000 and 5". A departure runway is stated only when it differs from the arrival runway.

The information letter

JO 7110.65 section 2-9 sets the rules for the letter:

  • the letter is spoken at the start and at the end of the recording;
  • letters run in sequence from Alpha to Zulu and are not reset at midnight;
  • after an interruption of more than 12 hours the sequence restarts at Alpha or the first assigned letter;
  • arrival and departure broadcasts can be separate.

A new recording is made whenever any new official weather is received, even if the values have not changed, when braking action is worse, and when the runway, the approach, NOTAMs or pilot reports change. If a pilot does not state the code, the controller says "Verify you have information Charlie" or the current letter. A code change is announced on all frequencies, as in "Attention all aircraft, information Alpha current".

An example from the AIM

The AIM gives this broadcast, written here as spoken:

Dulles International information Sierra. One four zero zero zulu.
Wind three five zero at eight. Visibility one zero. Ceiling four thousand
five hundred broken. Temperature three four. Dew point two eight.
Altimeter three zero one zero. ILS runway one right approach in use.
Departing runway three zero. Advise on initial contact you have
information Sierra.

It reads: information Sierra, weather as of 1400 UTC, wind 350 degrees at 8 knots, visibility 10, broken ceiling at 4,500 feet, temperature 34 and dew point 28, altimeter 30.10, ILS to runway 1R in use, departures from runway 30.

The pilot answers on first contact with the letter, for example "Information Sierra received", so that the controller knows which version the pilot has.

Have numbers

The AIM explains that "have numbers" means the pilot has only the wind, the runway and the altimeter setting. It does not mean the pilot has the ATIS, so the controller may still ask for the information letter.

Differences from a METAR

An ATIS is a locally prepared broadcast and a METAR is a coded observation. The ATIS adds operational information the observation does not carry: runway in use, approach, closures and notices. JO 7110.65 refers to a magnetic wind that can be included in an ATIS, taken from the automated observing system. The spoken report also uses plain words, so the codes seen on the remarks page do not appear as such.

United Kingdom practice

The UK AIP (GEN 3.5) says that weather information can be obtained from VOLMET, from ATIS and from D-ATIS where available, or by request to air traffic services. At aerodromes with the equipment, a marked temperature inversion warning is broadcast on the departure and arrival ATIS. The AIP defines it as a temperature difference of 10 C or more between the surface and any point up to 1,000 feet above the aerodrome. Wind shear warnings are broadcast too, as WINDSHEAR FORECAST (WSF), WINDSHEAR FORECAST AND REPORTED (WSFR) or WINDSHEAR REPORTED (WSR). The AIP also warns that an automated METAR on an ATIS may not have had its phenomena checked by a human observer. Wind shear coding is explained on the wind shear group page. For long-range broadcasts, see the VOLMET page.

Using the ATIS in practice

The sources give a clear sequence. The AIM describes the broadcast as a loop of routine information that spares the controller from repeating it to each aircraft, and JO 7110.65 requires the information letter to be stated on first contact or verified by the controller. A pilot who has copied the letter, the wind, the runway in use and the altimeter setting has the items the controller would otherwise read out. The altimeter setting is the figure to set on the subscale, so it deserves a careful read-back, and the qnh page explains how that value differs from other pressure settings.

Because a new recording is made when the official weather changes, even with unchanged values, a letter that differs from the one copied earlier means the pilot should listen again. The same rule applies after a change of runway or approach. When the ATIS has been omitted or shortened for good weather, the missing items come from the controller on request.

Method and limits

The content, service volume, shortened weather and "have numbers" come from AIM chapter 4, section 1 (section 4-1-13). The letter rules and the extra items come from JO 7110.65 chapter 2, section 9. The UK points come from the UK AIP GEN 3.5 (AIRAC of January 22, 2026). D-ATIS, the digital version delivered by data link, was not verified from a primary source for this page and is only named. The ICAO provisions for ATIS in Annex 11 and Annex 3 were not read. The Alaska flight information service (AFIS, AIM 4-1-14) is not covered. The photo shows the tower at Edinburgh Airport and is not tied to a broadcast.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What is an ATIS information letter?

Every recording starts and ends with a phonetic letter, from Alpha to Zulu. The letter changes with each new recording and does not reset at midnight. Pilots state it on first contact, for example information Sierra received, so the controller knows which version they have.

What does 'have numbers' mean?

The AIM says it means the pilot has only the wind, runway and altimeter. It does not mean the pilot has received the ATIS. The controller can still ask the pilot to confirm the information letter.

When is an ATIS updated?

In the United States, the controller records a new ATIS whenever any new official weather is received, even if the values are unchanged, and when braking action is worse or the runway, approach, NOTAMs or pilot reports change. A change of letter is announced on the frequency.

Is ATIS the same as a METAR?

No. The ATIS is a spoken, locally recorded broadcast that includes operational items such as runway and approach in use. A METAR is a coded observation. The ATIS weather comes from the latest observation, but it adds notices and can omit parts of the weather.

How far away can I hear an ATIS?

The AIM gives a normal service volume of 20 to 60 nautical miles and up to 25,000 feet above ground level for an arrival ATIS. A departure ATIS cannot exceed 5 nautical miles and 100 feet above ground level. Actual reception depends on the station.

Sources

  1. Federal Aviation Administration (2026). Aeronautical Information Manual, chapter 4, section 1 (Air Traffic Control Services)
  2. Federal Aviation Administration (2026). Order JO 7110.65, Air Traffic Control, chapter 2, section 9 (Automatic Terminal Information Service)
  3. NATS, United Kingdom (2026). United Kingdom AIP, GEN 3.5 Meteorological Services