Low level wind shear in a TAF: reading the WS group

Tafrob editorial team · Updated · 7 min read

Short answer

The WS group forecasts non convective low level wind shear. WS020/27055KT means wind shear from the surface up to 2,000 feet above ground, with a wind of 270 degrees at 55 knots at the top of that layer. The second part is the wind at that height, not the amount of shear. US and Canadian TAFs use it; it sits after the cloud group.

Key points

  • WS is followed by the top of the shear layer in hundreds of feet above ground, then the wind at that height.
  • The wind after the slash is a wind, not a shear value; compare it with the surface wind to see the change.
  • The group covers only non convective shear; shear is always assumed near thunderstorms.
  • In US TAFs it is the last group of a line and lasts until the next FM group or the end of the TAF.
  • It never appears in TEMPO or PROB groups.
  • The NWS works within 2,000 feet above ground; Transport Canada within 1,500 feet.
NASA researchers in the flight deck of a Boeing 737 during wind shear sensor flight tests
Photo: NASA/Langley Research Center, Public domain, via Wikimedia Commons

What the WS group warns about

Wind shear is a change in wind speed, direction, or both, over a short distance. Close to the ground it is dangerous because an aircraft on take off or approach has little height to recover from a sudden loss of airspeed. The Aviation Weather Handbook puts the risk simply: a sufficient difference in wind speed, wind direction, or both can severely impact airplanes, especially within 2,000 feet above ground level, because of the limited vertical airspace for recovery.

The TAF has a dedicated group for this hazard. NWS Instruction 10-813 calls it the non convective low level wind shear group, written WS followed by a height and a wind. It appears in US and Canadian TAFs. The pillar page on reading a TAF shows where it fits among the other elements.

The format

NWS Instruction 10-813 gives the group as WShwshwshws/dddffKT:

Part Example Meaning
WS WS Indicator for non convective low level wind shear
hwshwshws 020 Height of the top of the shear layer, in hundreds of feet above ground level
/ / Separator
ddd 270 True direction of the wind at that height, in tens of degrees
ff 55 Speed of the forecast wind at that height, in knots
KT KT Unit indicator

VRB is never used for the direction in this group, since a shear forecast needs a defined wind at the top of the layer.

The Pueblo example

The instruction gives this TAF for Pueblo, Colorado:

TAF
KPUB 181122Z 1812/1912 13012KT 5SM -RA SCT010 OVC035 WS020/27055KT
     FM181400 32010KT P6SM FEW008 BKN045...

The surface wind is 130 degrees at 12 knots. The WS group says wind shear is forecast from the surface up to 2,000 feet above ground, where the wind is 270 degrees at 55 knots. Between the ground and 2,000 feet the wind turns through 140 degrees and gains more than 40 knots. The group applies from 1200 UTC until the FM group at 1400 UTC.

A wind, not a shear value

The most common misreading of the group is to take 55KT as the strength of the shear. NWS Instruction 10-813 and the Aviation Weather Handbook both state that the five digit group after the slash is the wind direction and speed at the top of the layer and is not a value for the amount of shear.

The shear itself is the difference between the two winds as vectors. The NWS instruction quotes the ICAO Manual on Low level Wind Shear (Doc 9817) on this point: wind shear cannot be calculated by simple scalar subtraction of the wind speeds, except when the two winds have the same direction. In the Pueblo case, a change from a southeast wind to a strong west wind is a much larger vector change than the 43 knot difference in speed alone suggests.

Where the group sits and how long it lasts

The Aviation Weather Handbook and NWS Instruction 10-813 give the same placement rules for US TAFs:

  • The WS group is the last group of the line, after the cloud forecast.
  • Once in the TAF, it is a prevailing condition until the next FM group, or until the end of the valid period if no FM group follows.
  • It is not included in TEMPO or PROB groups.

This makes the FM group the natural boundary for wind shear. A line with WS describes shear for its whole duration, and a new FM line without WS ends it. The second NWS example shows the pattern at Dallas Fort Worth:

TAF
KDFW 220539Z 2206/2306 21010KT 3SM BR SCT030 WS015/29065KT
     FM221100 24015KT 1SM TSRA BR OVC010CB

Shear is forecast from the surface to 1,500 feet, with 290 degrees at 65 knots at that height, from 0600 UTC until 1100 UTC. The FM group at 1100 UTC brings thunderstorms and has no WS group, which does not mean the shear has gone: it means any shear is now convective and covered by the thunderstorm forecast.

When forecasters include it

NWS criteria

NWS Instruction 10-813 restricts the group to non convective shear from the surface up to 2,000 feet above ground. It lists frontal passages, inversions, low level jets, lee side mountain effects, sea breeze fronts, and Santa Ana, Chinook or foehn winds as typical causes, and highly encourages forecasters to mention shear whenever conditions are present or possible.

The instruction then sets thresholds:

  • The TAF should identify the lowest layer where the shear is at least 30 knots within 2,000 feet above ground. Offices may agree specialised thresholds with users and record them in the amendment criteria spreadsheet.
  • When several layers have shear, the lowest one is coded, because users have identified it as the most dangerous.
  • If shear is not in the TAF and pilot reports describe non convective shear within 2,000 feet causing an airspeed loss or gain of 30 knots or more, the TAF should be amended to include it.

The Aviation Weather Handbook gives the criteria in a different form. A WS group goes in the initial period or an FM group when pilot reports show a non convective shear causing an indicated airspeed loss or gain of 20 knots or more, judged to be shear rather than mechanical turbulence, or when shear of 10 knots or more per 100 feet in a layer more than 200 feet thick is expected or reliably reported within 2,000 feet of the surface. The 20 knot figure in the handbook and the 30 knot figure in the October 2024 instruction differ; the instruction is the more recent operational text for NWS forecasters.

A forecast that misses shear is an amendment criterion. The amended TAF page lists it with the ceiling, visibility and wind thresholds.

Shear or mechanical turbulence

Gusty surface winds do not automatically mean wind shear. NWS Instruction 10-813 explains that when the low level wind blows from nearly the same direction at all heights, a well mixed layer produces gusts at the surface and usually mechanical turbulence rather than shear. Strong directional change with height is the signal that a WS group may be needed. Gusts alone are coded in the wind group, as described on the METAR gusts page.

Transport Canada

The Canadian rule is narrower in height. TC AIM says the group is used if the forecaster has strong evidence to expect significant non convective wind shear that could adversely affect aircraft operation within 1,500 feet above ground over the aerodrome. It notes that the main effect of wind shear is a rapid gain or, more critically, loss of airspeed, and that shear cannot yet be satisfactorily observed from the ground, so aircraft reports and radiosondes are the only available evidence.

Its sample TAF for Saskatoon opens with:

TAF CYXE 281139Z 2812/2912 24010G25KT WS011/27050KT 3SM -SN BKN010 OVC040

Here the WS group follows the surface wind rather than the cloud group. TC AIM decodes it as wind shear forecast in the layer from the surface to 1,100 feet above ground, with a wind of 270 degrees true at 50 knots at the shear height. Low level wind shear at or below 1,500 feet is also one of the Canadian amendment criteria.

Convective shear is not coded

The group is limited to non convective shear. NWS Instruction 10-813 states that low level wind shear is always assumed to be present in convective activity. A TAF that forecasts thunderstorms or cumulonimbus already warns of shear, including microbursts and gust fronts, without a WS group. The thunderstorm page covers how storms are written in a TAF.

The METAR WS group is different

WMO-No. 782 describes a WS group in the METAR, such as WS R24 or WS ALL RWY. That group reports wind shear that has been observed along the take off or approach path of a runway. It is an observation, it names a runway, and it carries no height or wind. The TAF code form in WMO-No. 782, and the generic international format reproduced in NWS Instruction 10-813, do not include a forecast WS group. The METAR group is explained on the METAR wind shear page.

Reading it in practice

  • Compare the two winds. Set the WS wind against the surface wind of the same line. A large turn, a large speed change, or both is the hazard.
  • Remember the layer starts at the ground. WS015 means shear anywhere from the surface to 1,500 feet, which covers the final approach and the initial climb.
  • Check where it ends. In a US TAF the group lasts until the next FM line.
  • Treat thunderstorms separately. No WS group near TS or CB does not mean no shear.

The "In real reports" box on this page gives the share of TAFs in the NOAA Aviation Weather Center sample that contain a WS group.

Method and limits

The format, examples and criteria are quoted from NWS Instruction 10-813 (October 2024), the Aviation Weather Handbook and the Transport Canada AIM MET section. The Saskatoon line is shown on one line; the AIM prints it across several. The difference between the 20 knot and 30 knot pilot report thresholds is reported as found in the two FAA and NWS texts. Whether other national services outside the United States and Canada add a WS group to their TAFs by local agreement was not surveyed.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What does WS020/27055KT mean in a TAF?

Non convective low level wind shear is forecast from the surface to 2,000 feet above ground level, and the wind at 2,000 feet is from 270 degrees true at 55 knots. The Aviation Weather Handbook decodes its example with a surface wind of 130 degrees at 12 knots, so the wind turns and strengthens sharply through the layer.

Is the speed in the WS group the amount of wind shear?

No. NWS Instruction 10-813 and the Aviation Weather Handbook both state that the five digit group after the slash is the wind direction and speed at the top of the shear layer, not a value for the amount of shear. The shear is the vector difference between that wind and the surface wind.

Why is there no WS group when thunderstorms are forecast?

The group is for non convective wind shear only. NWS Instruction 10-813 states that low level wind shear is always assumed to be present in convective activity, so a thunderstorm forecast already implies it. Microbursts and gust fronts are not coded with WS.

Do European TAFs use the WS group?

The WMO TAF code form described in WMO-No. 782 and the generic international format in NWS Instruction 10-813 do not include a forecast WS group. The WS groups in WMO-No. 782 are observed wind shear on a runway, reported in the supplementary part of a METAR.

How long does the WS group apply?

In a US TAF it stays in force as a prevailing condition until the next FM group, or until the end of the valid period if no FM group follows. It is not written in TEMPO or PROB groups, so it cannot describe a short spell of shear.

Sources

  1. National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024), Appendix B2.8
  2. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A), sections 19.2.4.1 and 27.3.2.9.4
  3. Transport Canada (2025). TC AIM, MET section 7.0 Aerodrome forecasts (TAFs)
  4. World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition