QNH and altimeter setting in a METAR: Q1013 versus A2992

Tafrob editorial team · Updated · 5 min read

Short answer

The last group of the METAR body is the pressure for the altimeter. ICAO reports use Q and four digits in hectopascals, as in Q1013. The US and Canada use A and four digits in inches of mercury, with the decimal point left out, so A2992 means 29.92. Both are rounded down, never up, to the next reportable value.

Key points

  • Q means hectopascals and A means inches of mercury; the letter tells you the unit, so check it before reading the digits.
  • The US altimeter setting is four digits with no decimal point: A2992 is 29.92 inHg and A3005 is 30.05 inHg.
  • Pressure values are rounded down to the next reportable value, not to the nearest one.
  • QNH is pressure corrected to mean sea level, and QFE is pressure corrected to a specific elevation such as the aerodrome or the runway threshold.
  • A pressure under 1000 hPa keeps a leading zero after the Q, for example Q0987.
Instrument panel of a Piper PA-28 light aircraft with the altimeter among the flight instruments
Photo: Myself (Adrian Pingstone)., Public domain, via Wikimedia Commons

What does the pressure group tell a pilot?

The pressure group is the last group of the main body of a METAR, and it gives the setting that makes an altimeter read correctly. WMO-No. 782 says the last group of the main part of the report indicates the QNH, which it calls the mean sea level pressure. The FMH-1 handbook defines the altimeter setting as the pressure value to which an aircraft altimeter scale is set so that it indicates the altitude above mean sea level of an aircraft on the ground at the location for which the value was determined.

The two definitions describe the same practical idea. Set the number from the report on the altimeter, and an aircraft on the ground at that place reads its elevation. For the position of this group in a full report, see how to read a METAR.

ICAO format: Q and hectopascals

WMO-No. 782 writes the group as QPHPHPHPH. It starts with the letter Q followed by four figures, the QNH rounded down to the nearest whole hectopascal. CAP 746 gives the same rule and adds that if the value is below 1000 hPa a zero follows the Q.

QNH Coded as
987 hPa Q0987
995.6 hPa Q0995
1001 hPa Q1001
1023 hPa Q1023

The values 987, 1001 and 1023 are CAP 746 examples, and 995.6 hPa is the WMO-No. 782 example. Note that 995.6 becomes Q0995, not Q0996. Rounding down means the coded value can be lower than the measured one by almost one hectopascal.

US and Canadian format: A and inches of mercury

FMH-1 says the altimeter group always starts with an A, the international indicator for altimeter in inches of mercury. It is coded as four digits immediately after the A, using tens, units, tenths and hundredths of inches, with the decimal point not coded. WMO-No. 782 shows the same convention for countries that use inches: a QNH of 30.05 inches of mercury is reported as A3005.

NAV CANADA uses the same pattern. Its guide decodes A2992 as 29.92 inches of mercury and A2926 as 29.26 inches, and says the letter A prefixing the four-digit group indicates inches of mercury.

Group Value
A2992 29.92 inHg
A3005 30.05 inHg
A2926 29.26 inHg

How is the value rounded?

Both systems round down. FMH-1 states that when a pressure value must be rounded to a reportable value, it is rounded down to the next reportable value. Its example is an altimeter reading of 29.248 inches of mercury, which becomes 29.24 inches. WMO-No. 782 and CAP 746 round QNH down to the nearest whole hectopascal.

This differs from the rounding of temperature, where a half degree goes up. See temperature and dew point for that rule.

QNH, QFE and the standard value

CAP 746 gives two definitions in its glossary:

  • QNH is the atmospheric pressure corrected to mean sea level, assuming International Standard Atmosphere conditions across the height difference.
  • QFE is the atmospheric pressure corrected to a specific elevation, for example the official aerodrome elevation or the runway threshold elevation.

CAP 746 also says that the METAR must carry the aerodrome QNH, the mean sea level pressure, and not the threshold pressure. CAP 746 also says QNH and QFE should be available to an accuracy of one tenth of a hectopascal on request. This page does not define QNE, because no source opened for it gave a definition.

For the standard atmosphere, the Aviation Weather Handbook lists sea level pressure as 1013.25 hPa and 29.92 inHg. Its unit table gives 1013.2 hPa as the standard value in the METAR and SPECI hectopascal unit, and 29.92 inHg for US aviation. The handbook also says pressure altitude is the altitude shown by the altimeter when it is set to 29.92 inHg.

Converting between hPa and inHg

The report you read decides the unit, and the two scales are not interchangeable by eye. The anchor point from the FAA handbook is that 29.92 inHg is the same pressure as 1013.2 hPa. Do not convert a setting in your head and rely on it, because the reporting step differs: a whole hectopascal is a larger step than a hundredth of an inch. The pressure converter does the conversion and shows both values. The comparison across countries is in units in METAR by country.

Decoding examples

NAV CANADA prints this report with a US-style altimeter group:

METAR CYXE 292000Z CCA 30015G25KT 3/4SM R33/4000FT/D -RA BR BKN008 OVC040 21/19 A2992 WS RWY33 RMK SF5NS3 VIS NW 3/8 SLP134 DENSITY ALTITUDE 2500FT
  • A2992: altimeter setting 29.92 inches of mercury.
  • SLP134: a separate remark with the sea level pressure in hectopascals, decoded by the guide as 1013.4 hPa. It is not the group you set on the altimeter. See sea level pressure SLP.

The FAA handbook gives a US report that ends in the same group:

METAR KOKC 011955Z AUTO 22015G25KT 180V250 3/4SM R17L/2600FT +TSRA BR OVC010CB 18/16 A2992
  • A2992: 29.92 inHg. In an ICAO report, the equivalent group would start with Q and carry whole hectopascals.

Quick way to tell the two groups apart

Look at the first letter before the digits. A group starting with Q is an ICAO report in whole hectopascals, and the number is usually near 1000, so a leading zero appears only when the value is below 1000. A group starting with A is in inches of mercury, and the number is usually near 3000 because the decimal point is dropped. Both groups have four digits, which is why the letter matters. Read the digits without the letter and Q1013 could be mistaken for an inch value with a missing decimal point. Rounding also differs in practice: the hectopascal group steps in whole units, while the inch group steps in hundredths.

Common mistakes

  • Reading A2992 as 2992 hPa. The letter A means inches, and the decimal point is missing.
  • Reading Q1013 as 10.13 or 1013 inHg. Q means hectopascals.
  • Confusing the altimeter group with the SLP remark. The remark is for meteorologists, the body group is for the altimeter.
  • Assuming the report is rounded to the nearest value. It is rounded down.

This page is educational and is not a source for operational weather. For the full list of differences, see US versus ICAO METAR differences.

Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).

Frequently asked questions

What is the difference between Q1013 and A2992?

They are two ways of writing a pressure setting. Q1013 is hectopascals, used in ICAO countries, and A2992 is 29.92 inches of mercury, used in the US and Canada. The FAA handbook lists 1013.2 hPa and 29.92 inHg as the same standard sea level value, so they are close but not the same report.

Is the METAR pressure rounded or truncated?

It is rounded down. WMO-No. 782 says QNH is rounded down to the nearest whole hectopascal, so 995.6 hPa is Q0995. FMH-1 rounds pressure values down to the next reportable value, so an altimeter of 29.248 inHg becomes 29.24, not 29.25.

What is the difference between QNH and QFE?

CAP 746 defines QNH as pressure corrected to mean sea level, assuming International Standard Atmosphere conditions across the height difference. QFE is pressure corrected to a specific elevation, such as the aerodrome elevation or the runway threshold. The METAR carries QNH, not QFE.

Why does a METAR show Q0987 with a zero?

The group always has four digits after the Q. CAP 746 says that if the value is less than 1000 hectopascals, a zero is inserted after the Q. So 987 hPa is written Q0987 and 1001 hPa is written Q1001. Without the zero the group would be only three digits.

Sources

  1. Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1 (FCM-H1-2019)
  2. Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
  3. World Meteorological Organization (2025). Aerodrome Reports and Forecasts, A Users' Handbook to the Codes (WMO-No. 782)
  4. UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
  5. NAV CANADA. Aviation Weather Services Guide