VV: vertical visibility when the sky is obscured
VV stands for vertical visibility. It replaces the cloud group when fog, snow or another obscuration hides the sky, so no cloud base can be seen. The three digits give, in hundreds of feet, how far the observer or sensor can see upward: VV003 is 300 feet. VV counts as a ceiling, and VV/// means the vertical visibility could not be assessed.
Key points
- VV replaces the cloud group when the whole sky is hidden by an obscuration such as fog or snow.
- The digits are hundreds of feet: VV002 is 200 feet, VV010 is 1,000 feet.
- VV is a ceiling: FMH-1 and the FAA AIM call it an indefinite ceiling.
- VV/// means the vertical visibility could not be assessed.
- In the UK, vertical visibility is not assessed, so CAP 746 uses VV/// instead.
- A TAF uses VV when the sky is expected to stay or become obscured.

When the sky cannot be seen
A cloud group needs a cloud base. When fog, heavy snow or another obscuration covers the station, the observer looks up and sees no base at all, only a grey mass that fades with height. The METAR then drops the usual FEW, SCT, BKN or OVC groups and reports a vertical visibility instead: how far the observer, or the sensor, can see straight up into the obscuration.
| Code | Meaning |
|---|---|
VV001 |
Vertical visibility 100 feet |
VV003 |
Vertical visibility 300 feet |
VV010 |
Vertical visibility 1,000 feet |
VV/// |
Sky obscured, vertical visibility not assessed |
1/8SM FG VV006 |
US: fog, indefinite ceiling 600 feet |
How to read the digits
The format is the letters VV followed by three digits. FMH-1 (section 12.6.9) writes it as VVhshshs, where the three digits are the vertical visibility in hundreds of feet, the same unit as cloud heights. VV002 is 200 feet and VV012 is 1,200 feet. WMO-No. 782 gives the example VV003, a vertical visibility of 300 feet.
The digits follow the same reporting steps as cloud bases, explained on the cloud height page. In practice the values are almost always low, a few hundred feet, because a deep obscuration that still allows a long vertical view usually leaves a cloud base visible instead.
When VV is used
VV is used only when the sky is totally hidden. FMH-1 (section 9.4.5) states that when the sky is totally obscured, the vertical visibility is reported and it is the ceiling. A partial obscuration, such as a fog bank covering part of the sky while cloud remains visible above, is not coded with VV in US practice; the visible layers are reported and the obscuration is described in other groups and remarks.
The usual causes are fog and heavy snow. CAP 746 (section B.13) lists other phenomena that can hide the sky: blowing dust, blowing sand, volcanic ash and spray. The weather group of the same report names the cause, so VV is almost always read together with codes such as FG or SN. Fog and its forms are explained on the FG fog page.
How vertical visibility is measured
FMH-1 (section 9.4.4) lists four ways to obtain the value:
- the distance an observer can see vertically into the indefinite ceiling;
- the height at which the beam of a ceiling light ends;
- the height at which a ceiling balloon disappears from view;
- the value computed by the sensor algorithm at an automated station.
All four describe how far one can see, not the height of a physical surface. FMH-1 (9.4.7.a) reports the result in hundreds of feet. At automated stations the value comes from the ceilometer, whose processing is explained on the ceilometer page.
VV as a ceiling
A vertical visibility counts as a ceiling. The FAA AIM defines the ceiling as the lowest layer reported as broken, overcast or obscuration, and gives the reading of 1/8 SM FG VV006: visibility one eighth of a statute mile in fog, indefinite ceiling six hundred. FMH-1 uses the same rule. The full ceiling rule is on the ceiling page.
The word "indefinite" is important. Because the obscuration has no sharp base, a pilot on approach may see the ground earlier or later than the reported value suggests, and the slant view through fog differs from the vertical one. VV is a measure of the obscuration at the station, not a promise of when the runway will appear. Horizontal visibility, reported in the visibility group and explained on the visibility page, and runway visual range often matter more for the approach itself.
VV/// and the UK practice
WMO-No. 782 uses VV/// when the sky is obscured but the vertical visibility cannot be assessed. This is common at automatic stations, where the sensor may detect that the sky is hidden without being able to measure how far it can see.
The United Kingdom goes further. CAP 746 (sections 4.102 and 4.111) states that in the UK vertical visibility is not assessed, so an obscured sky is always reported as VV///. A UK report with fog and a hidden sky therefore never shows digits after VV.
CAP 746 (section B.13) gives guidance on when to use the code: an observer should consider VV/// when the visibility is below 200 m, because the sky is then likely to be obscured. Section B.14 adds a case seen with automatic systems: an automatic report of OVC002 with a visibility of 200 m in fog probably corresponds to an obscured sky, which a human observer would report as VV///.
VV in a TAF
WMO-No. 782 allows VV in a TAF when the sky is expected to remain or become obscured. A forecast of fog at night can therefore carry a change group such as TEMPO 0204/0208 0200 FG VV001, with the vertical visibility as the forecast ceiling. When the fog is expected to lift into a layer of stratus, the VV group is replaced by an ordinary cloud group, such as BKN003.
Reading VV with the rest of the report
VV almost never stands alone. The typical sequence in a report is a low visibility, a fog or snow code, then VV:
0150 FG VV001: 150 m in fog, vertical visibility 100 feet;1/4SM SN VV004: US report, a quarter of a mile in snow, vertical visibility 400 feet;0100 FG VV///: 100 m in fog, sky obscured, vertical visibility not assessed.
The cloud codes used once the sky becomes visible again are on the cloud cover codes page. A report that moves from VV001 to OVC002 an hour later usually describes fog lifting into a low stratus deck rather than a sudden change in the weather.
A schematic report
METAR LXXX 190620Z 00000KT 0150 R27/0300N FG VV001 05/05 Q1024
It reads: calm wind, visibility 150 m, runway visual range on runway 27 of 300 m with no change, fog, vertical visibility 100 feet, temperature and dew point both 5 °C. The ceiling is 100 feet, an indefinite ceiling. A UK station would report the same sky as VV///.
In real reports
The "In real reports" box on this page shows the share of METARs in the NOAA Aviation Weather Center sample collected for this site that contain a VV group. Fog and heavy snow are short events at most stations, so the share is small, and it rises at night and in the early morning, when radiation fog forms.
Method and limits
Definitions and rules are taken from FMH-1 (2019, sections 9.4.4, 9.4.5, 9.4.7 and 12.6.9), WMO-No. 782 (2025 edition, cloud group and TAF), CAP 746 (sections 4.102, 4.111, B.13 and B.14) and the FAA AIM, chapter 7, section 1. The VV003 and 1/8 SM FG VV006 readings are quoted examples; the TEMPO line, the three short groups and the LXXX line are schematic examples, not real reports. The image shows an airliner landing in fog at Boston; it is not linked to a specific report. The box counts VV groups in the text of the METARs, including VV///.
Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).
Frequently asked questions
What does VV mean in a METAR?
VV means vertical visibility. It is used when the sky is totally hidden by fog, snow or another obscuration, so no cloud base can be reported. VV004 means the observer or sensor can see 400 feet upward into the obscuration.
Is vertical visibility a ceiling?
Yes. FMH-1 states that the vertical visibility is the ceiling when the sky is totally obscured, and the FAA AIM reads 1/8 SM FG VV006 as an indefinite ceiling of six hundred feet. Pilots treat it like the lowest broken or overcast layer.
What does VV/// mean?
It means the sky is obscured but the vertical visibility could not be assessed. WMO-No. 782 uses VV/// in that case. In the UK, CAP 746 states that vertical visibility is not assessed, so an obscured sky is always reported as VV///.
How is vertical visibility measured?
FMH-1 lists four methods: the distance an observer can see vertically into the obscuration, the height at which a ceiling light beam ends, the height at which a ceiling balloon disappears, and the value computed by the sensor algorithm at automated stations.
Why is VV called an indefinite ceiling?
Because there is no sharp cloud base. In fog or heavy snow the obscuration fades gradually upward, so the reported value is how far the eye or sensor can see, not the height of a surface. The real conditions on approach can differ from it.
Sources
- Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FCM-H1-2019)
- World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition
- UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
- Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1