TEMPO vs BECMG vs FM: the TAF change groups compared
FM starts a complete new forecast at an exact time and replaces everything before it. BECMG describes a lasting change that happens at some point inside a period of up to 4 hours. TEMPO describes short fluctuations, each under 1 hour, after which the prevailing conditions return. FM and BECMG change the base forecast; TEMPO does not.
Key points
- FM is a clean break at a stated minute and restates every element.
- BECMG is a lasting change at an unspecified time within its period, normally 1 to 2 hours, at most 4.
- TEMPO is a temporary change: each spell under 1 hour, all spells under half the period.
- After FM and BECMG the new conditions persist; after TEMPO the previous ones apply again.
- NWS TAFs use FM and TEMPO but not BECMG.

Three groups, three kinds of change
A TAF starts with a prevailing forecast and then lists how it is expected to change. Three groups do most of that work, and each answers a different question about the change: when it happens, how long it lasts, and what it replaces.
- FM (from) says the forecast changes at a precise time and gives the complete new forecast.
- BECMG (becoming) says the forecast changes for good at some point inside a period.
- TEMPO (temporarily) says the forecast will fluctuate for short spells inside a period and then return.
Probability groups add a fourth layer on top of these, and they are covered separately on the PROB30 and PROB40 page. The pillar page on reading a TAF shows the groups in context.
Comparison table
| Feature | FM | BECMG | TEMPO |
|---|---|---|---|
| Meaning | From this time, a new forecast | Conditions changing at an unspecified time in the period | Temporary fluctuations in the period |
| Time format | FMddhhmm, to the minute |
DDHH/DDHH, whole hours |
DDHH/DDHH, whole hours |
| Length | Lasts until the next FM or the end of validity | EU: period not over 4 hours. Canada: normally 1 to 2 hours, not over 4 | Each spell under 1 hour, all spells under half the period. NWS: period not over 4 hours |
| Effect after the group | New prevailing conditions | New prevailing conditions | Previous conditions apply again |
| Elements written | All elements | Only changed elements, all cloud layers if cloud changes | Only changed elements, all cloud layers if cloud changes |
| Used by the NWS | Yes | No | Yes |
The duration figures come from Regulation (EU) 2017/373, NWS Instruction 10-813 and the Transport Canada AIM. The NWS position on BECMG comes from Appendix E2 of the NWS instruction, which lists BECMG among the items not used in NWS TAFs.
FM: a clean break
An FM group restates everything. NWS Instruction 10-813 requires all elements to be repeated in an FM group, writes the time to the minute, and starts each FM on a new line. Nothing written before it carries forward. This is what makes FM the simplest group to read: the line after FM is the whole forecast until the next FM.
KDSM 022336Z 0300/0400 20015KT P6SM BKN015
FM030230 29020G35KT 1SM +SHRA OVC005
TEMPO 0303/0304 30030G45KT 3/4SM -SHSN
FM030500 31010G20KT P6SM SCT025
This NWS example has all three ideas in four lines. From 0230 UTC on the 3rd the wind veers to 290 degrees with heavy rain showers and a 500 foot overcast. Between 0300 and 0400 UTC there are short spells of stronger gusts and light snow showers. From 0500 UTC a new forecast replaces everything with 6 miles or more and scattered cloud. More on the FM group page.
BECMG: a gradual, lasting change
A BECMG group changes the forecast for good, but the code does not say when inside the period the change happens. The Regulation (EU) 2017/373 text limits the period to 4 hours, and Transport Canada says the change normally takes 1 to 2 hours. Only the elements that change are written, so everything else carries forward from the line before.
TAF LUDO 130530Z 1307/1316 31015KT 8000 RA SCT006 BKN012
BECMG 1312/1314 NSW SCT025
In this WMO-No. 782 example, rain ends and the cloud lifts to a scattered layer at 2,500 feet some time between 1200 and 1400 UTC. The wind and the visibility are not mentioned, so they stay at 310 degrees, 15 knots and 8000 metres. After 1400 UTC the new conditions are the prevailing ones. More on the BECMG page.
TEMPO: short spells, then back
A TEMPO group does not change the base forecast. It adds spells of different weather that come and go. The EU text limits each spell to under 1 hour and requires the spells to cover less than half the period in total. NWS Instruction 10-813 adds that the condition must have a probability above 50 percent and that the TEMPO period does not exceed 4 hours. If a condition lasts longer, the NWS says to use FM, and the EU text says BECMG or FM.
FM281100 VRB03KT 3SM RA BR OVC020
TEMPO 2812/2815 1SM RA BR
In this Transport Canada example, visibility drops to 1 mile in rain and mist for short spells between 1200 and 1500 UTC. Between those spells, and after 1500 UTC, the FM conditions apply: 3 miles and overcast at 2,000 feet. More on the TEMPO page.
Common misreadings
Reading BECMG as happening at the start of its period. The change can come at any time within the period, including the last minutes. Planning rules settle which time to assume, not the code.
Reading TEMPO as lasting the whole window. A TEMPO 2812/2815 does not mean three hours of reduced visibility. It means spells of under 1 hour each, adding up to less than half of the forecast period.
Carrying old elements past an FM. After an FM, nothing from the earlier lines applies. A reader who keeps an earlier visibility or cloud layer has misread the group.
Forgetting elements after a BECMG. The opposite mistake: after BECMG, elements that are not mentioned are unchanged and still apply.
Expecting conditions to stay after a TEMPO. Once the TEMPO period ends, the forecast in force before it is the one that holds.
Confusing the TAF groups with the TREND. A METAR TREND also uses BECMG and TEMPO, but with different time words (FM, TL, AT) and a 2 hour horizon, as explained on the TREND and NOSIG page.
How planning rules treat each group
The code describes the weather. How each group counts for a dispatch or alternate decision depends on the rules the operator follows. The sources cited here give two general statements.
NWS Instruction 10-813 says that the lowest condition in a TAF, including PROB and TEMPO groups, drives user decisions. A TEMPO that looks like a short spell can still be the condition that matters.
Transport Canada gives a rule for BECMG when selecting an IFR alternate. When conditions are improving, the new conditions are considered to apply at the end of the change period. When they are deteriorating, they are considered to apply at the start. This takes the worst case in both directions.
For FM, the change time is given to the minute, so the new conditions apply from that minute. The flight planning page covers alternate rules in more detail, and the TAF decoder lays each group out on its own row.
Method and limits
The definitions and limits come from NWS Instruction 10-813, Regulation (EU) 2017/373, WMO-No. 782, the Transport Canada AIM MET section and the Met Office GetMet leaflet. The code lines are quoted from those documents, with line breaks and indentation adjusted for reading. The plain language readings are added for this page. Operator rules for TEMPO and PROB in alternate planning vary and are not covered in full here.
Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).
Frequently asked questions
What is the main difference between TEMPO and BECMG?
BECMG describes a permanent change: once its period ends, the new conditions are the prevailing ones. TEMPO describes temporary fluctuations that come and go inside the period, each under 1 hour, and the prevailing conditions apply again in between and afterwards.
When is FM used instead of BECMG?
FM is used for a rapid change at a known time, and it restates the whole forecast. Transport Canada also asks forecasters to keep BECMG to a minimum and to use FM when more than two groups change. NWS TAFs do not use BECMG at all, so every lasting change in a US TAF is an FM group.
During a BECMG period, which conditions should be assumed?
The code does not say when the change happens inside the period. For alternate planning, Transport Canada says improving conditions apply from the end of the period and deteriorating conditions from the start. Other operators have their own rules, so the applicable operations manual decides.
Does TEMPO need all elements repeated like FM?
No. TEMPO lists only the elements that change, like BECMG. FM is the only change group that restates every element. Cloud is the exception for TEMPO and BECMG: a significant cloud change needs all cloud layers to be written.
Sources
- National Weather Service (2024). NWS Instruction 10-813, Terminal Aerodrome Forecasts (October 30, 2024)
- European Union (EUR-Lex) (2017). Commission Implementing Regulation (EU) 2017/373, Annex V (Part-MET), aerodrome forecasts and TAF template
- Transport Canada (2025). TC AIM, MET section 7.0 Aerodrome forecasts (TAFs)
- World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition
- Met Office (2024). GetMet: aerodrome forecast TAF decode