Ceilometer: how airports measure cloud height
A ceilometer is an instrument that measures the height of cloud bases or the vertical visibility straight above it. Automated stations build the cloud group of a METAR from its readings over the last 30 minutes. A US ASOS ceilometer reports cloud up to 12,000 feet, so CLR means no cloud detected at or below that height, not a clear sky.
Key points
- FMH-1 defines a ceilometer as a device that evaluates cloud height or vertical visibility.
- It looks straight up, so it only sees cloud that passes over the sensor.
- Automated stations use 30 minutes of ceilometer data for clouds and 10 minutes for visibility.
- A US ASOS reports cloud up to 12,000 feet; higher layers are not reported.
- CLR from an automated station means no layer detected at or below 12,000 feet.
- A second sensor can add a remark such as CIG 002 RWY11.

A sensor that looks straight up
Most cloud heights in today's METARs come from a ceilometer. FMH-1 defines it in its glossary as a device used to evaluate the height of clouds or the vertical visibility into a surface based obscuration. The instrument sits on the ground, points straight up and records the height at which it detects cloud above it. Everything an automated station reports about the sky starts there.
| Code | Meaning |
|---|---|
BKN012 |
Layer built from ceilometer hits over 30 minutes |
CLR |
US automated: no layer detected at or below 12,000 feet |
VV002 |
Sensor value for vertical visibility into an obscuration |
CIG 002 RWY11 |
Ceiling from a second sensor, near runway 11 |
SKY CONDITION MISSING |
AWOS broadcast: cloud data not available |
From hits to layers
A ceilometer measures only a narrow column of sky. It does not see the whole dome, as a human observer does; it sees what passes over it. The automated station turns that single column into a sky description by letting time do the work of space: as the wind moves cloud across the sensor, the readings over a period sample the layers around the station.
The FAA Aviation Weather Handbook and FMH-1 (section 2.7.1) describe the windows used: the last 30 minutes of data for clouds, and the last 10 minutes for visibility. The algorithm groups the heights it has recorded into layers, estimates how often each layer was detected, and converts that into an amount, FEW, SCT, BKN or OVC. The Handbook adds that the processing gives more weight to changes toward worse conditions, so a lowering ceiling is reported faster than an improving one.
The FAA AIM, describing AWOS, gives the same picture: the ceilometer is placed near the visibility sensor, its report integrates the last 30 minutes, and the result depends on cloud passing over the sensor. On a calm day with a stationary cloud bank a few miles away, the ceilometer may report nothing at all.
The 12,000 foot limit
The range of the sensor sets the top of the report. The FAA Aviation Weather Handbook gives 12,000 feet for ASOS and notes that a future upgrade may raise the height limit. The FAA AIM states that clouds above 12,000 feet cannot be reported by an automated station.
This explains the meaning of CLR. FMH-1 and the Handbook use CLR at automated stations when no layer is detected at or below 12,000 feet. Cirrus at 25,000 feet, or an altocumulus layer at 15,000 feet, can be present under CLR. The no cloud codes are compared on the SKC, CLR, NSC and NCD page.
Other ways to measure cloud height
The ceilometer is one method among several. FMH-1 (section 9.4.7) lists, for manual and augmented observations, a ceilometer, a ceiling light, or the known heights of unobscured portions of isolated objects such as hills or towers within 1 1/2 statute miles of a runway. When none of those is available, the observer may use a ceiling balloon, pilot reports or experience.
The ceiling light and the ceiling balloon are the older tools. A ceiling light throws a beam onto the cloud base and the observer measures the angle to the spot; a ceiling balloon rises at a known rate and is timed until it disappears. FMH-1 still names both, and they also serve to estimate the vertical visibility, as explained on the vertical visibility page.
Automated, augmented and manual reports
A report built only from sensors carries the AUTO marker, explained on the AUTO, COR and NIL page. In the United States, the remark AO2 or AO1 tells the reader which sensors the station has, as explained on the AO1 and AO2 page. At augmented stations an observer can add what the ceilometer cannot see: high cloud, cumulonimbus, and layers that do not pass over the sensor.
WMO-No. 782 describes the forms used when an automatic system detects only part of the information. BKN/// means a layer is detected but its height is not available, and NCD means no cloud detected by an automatic system. The cloud type, CB or TCU, cannot come from a ceilometer, which measures height but not shape.
A second sensor
Some airports install a second ceilometer, usually near an approach end, where the cloud base can differ from the main site. FMH-1 (section 12.7.1.u) provides a remark for it: CIG hhh [LOC], as in CIG 002 RWY11, a ceiling of 200 feet measured at the sensor near runway 11. The remark follows RMK at the end of the METAR.
When the sensor fails
A ceilometer can stop reporting. In an AWOS broadcast the cloud part is then replaced by "SKY CONDITION MISSING", as described in the FAA AIM. In a METAR, a missing or faulty sensor shows up in the maintenance indicator and in sensor status remarks, explained on the sensor status page. The reader then has no cloud data at all from the station and must rely on nearby reports, forecasts or pilot reports.
Reading automated cloud groups
Three practical points follow from the way the sensor works:
- The amount is a time average over one spot, not a view of the whole sky. Scattered cloud that drifts over the sensor often may appear as BKN, and the reverse is also possible.
- A layer above 12,000 feet is never in a US automated report.
- A sudden lowering appears quickly, while an improvement takes longer to show, because the processing favours the worse value.
None of these makes an automated report wrong. They define what the report can and cannot say, and they explain most disagreements between an AUTO report and what a pilot sees overhead.
A schematic report
METAR LXXX 190855Z AUTO 21009KT 10SM FEW030 BKN048 14/08 A2994 RMK AO2 CIG 038 RWY29
It reads: automated report, wind from 210 degrees at 9 knots, visibility 10 statute miles, few clouds at 3,000 feet, broken at 4,800 feet, with a second sensor near runway 29 measuring a ceiling of 3,800 feet. Any cloud above 12,000 feet is absent from the report.
In real reports
This page has no "In real reports" box. A ceilometer is an instrument, not a code, so there is nothing to count directly. The box on the SKC, CLR, NSC and NCD page shows how often CLR appears in the NOAA Aviation Weather Center sample collected for this site, which gives an idea of how many reports come from automated sensors.
Method and limits
Definitions and rules are taken from FMH-1 (2019, glossary, sections 2.7.1, 9.4.7 and 12.7.1.u), the FAA Aviation Weather Handbook (FAA-H-8083-28A, automated observations), the FAA AIM, chapter 7, section 1 (AWOS and automated stations) and WMO-No. 782 (2025 edition, automatic forms). The description of the ceiling light and ceiling balloon is a general explanation of the methods named in FMH-1. The page does not describe the measuring principle of specific ceilometer models. The LXXX line is a schematic example, not a real report. The image shows the ASOS ceilometer at Ely Airport, Nevada; it is not linked to a specific report.
Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).
Frequently asked questions
What is a ceilometer?
It is an instrument that measures the height of cloud bases, or the vertical visibility into an obscuration, directly above the station. FMH-1 defines it as a device used to evaluate the height of clouds or the vertical visibility into a surface based obscuration.
How high can an airport ceilometer see?
The FAA Aviation Weather Handbook gives 12,000 feet for ASOS, and notes that a future upgrade may raise the limit. The FAA AIM states that clouds above 12,000 feet cannot be reported by an automated station, so high cloud is missing from those reports.
Why does an automated METAR show CLR under cirrus?
Because CLR only means that the ceilometer detected no layer at or below 12,000 feet. Cirrus is much higher, so it is outside the range of the sensor. A human observer at the same station would report the cirrus layer.
How does a ceilometer turn readings into cloud layers?
The station processes the hits recorded over the last 30 minutes. The FAA Aviation Weather Handbook and the AIM describe this 30 minute window for clouds, with a 10 minute window for visibility. Changes toward worse conditions are reported more quickly.
What does SKY CONDITION MISSING mean?
It is the message an AWOS broadcast gives when the cloud sensor data are not available. The station then cannot report any cloud layer or ceiling, and the pilot must find the sky condition from another source.
Sources
- Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FCM-H1-2019)
- Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)
- Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1
- World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition