Cloud height coding: the three digits after FEW, SCT, BKN and OVC
The three digits after a cloud amount give the height of the layer base in hundreds of feet above the aerodrome. BKN012 is a broken layer at 1,200 feet. WMO rules round down to 100 foot steps up to 10,000 feet and 1,000 foot steps above. US rules add 500 foot steps between 5,000 and 10,000 feet.
Key points
- The three digits are hundreds of feet: 008 is 800 feet, 045 is 4,500 feet, 250 is 25,000 feet.
- The height is above the aerodrome or the station, not above mean sea level.
- WMO-No. 782 and CAP 746 round down to 100 feet up to 10,000 feet, then to 1,000 feet.
- FMH-1 uses 100 foot steps up to 5,000 feet, 500 foot steps up to 10,000 feet, then 1,000 foot steps.
- A base at ground level is coded 000; slashes replace a height that is unknown or below the station.
- Pilot reports and some area products give cloud heights above mean sea level instead.

Three digits, hundreds of feet
Every cloud layer in a METAR or TAF ends with three digits. They give the height of the base of the layer in units of 100 feet, so the reader multiplies by 100 to get feet. The code is short because it is coarse: the value is a reporting step, rounded down, not a precise measurement.
| Code | Meaning |
|---|---|
FEW008 |
Few clouds, base 800 feet |
SCT018 |
Scattered, base 1,800 feet (a measured 1,850 is rounded down) |
BKN045 |
Broken, base 4,500 feet |
OVC000 |
Overcast at the surface |
BKN120 |
Broken, base 12,000 feet |
BKN/// |
Broken, height not available |
Above the aerodrome, not above sea level
The height in a METAR or TAF is measured from the ground at the station. CAP 746 (section 4.105) states that cloud heights are given above aerodrome level, and the FAA AIM (section 7-1-14) defines the ceiling as a height above ground or water level. The number can therefore be compared directly with the decision height of an approach or with the height a pilot plans to fly over the airfield.
The FAA AIM also notes that pilot reports and area forecasts give cloud heights above mean sea level. A PIREP that reports tops or bases at 3,500 feet over an airport at 1,200 feet elevation describes a base at about 2,300 feet above the ground. Mixing the two references is a common source of error, especially in hilly terrain where airport elevations vary a lot from one field to the next.
WMO and UK steps
WMO-No. 782 sets the reporting steps used in most of the world: 100 feet (30 m) up to 10,000 feet, and 1,000 feet above that. A layer at 4,750 feet is reported as 047, and a layer at 14,300 feet as 140. CAP 746 (section 4.109) applies the same rule in the United Kingdom.
Values are always rounded down to the step below. The WMO example is a layer of 3 oktas at 1,850 feet, reported as SCT018. Rounding down means the reported base is never higher than the real one, which keeps the error on the safe side for a pilot looking for cloud clearance. CAP 746 adds that a base below 100 feet is reported as 000.
US steps
FMH-1 (Table 9-7) uses a finer scale in the middle levels:
- to the nearest 100 feet up to 5,000 feet;
- to the nearest 500 feet above 5,000 feet and up to 10,000 feet;
- to the nearest 1,000 feet above 10,000 feet.
When a value falls exactly halfway between two steps, FMH-1 reports the lower one. A layer at 6,200 feet becomes 060, and a layer at 7,300 feet becomes 075. FMH-1 also codes any layer 50 feet or less above the surface as 000. The broader differences between the two rule sets are listed on the US and ICAO differences page.
In practice a reader rarely needs the exact step. The useful point is that a height above 5,000 feet in a US report, or above 10,000 feet anywhere, is an approximate value, and two stations close to each other can show different numbers for the same layer.
Height of what
The height is that of the base of the layer, the lowest level at which the cloud appears. FMH-1 (9.4.7) defines it as the height of the cloud bases or obscurations for the layer being evaluated. The digits say nothing about the thickness of the layer or its tops: OVC008 can be a thin sheet of stratus with clear sky at 1,500 feet, or the base of a cloud mass several thousand feet deep.
Each layer has its own height, and the groups are written from the lowest to the highest. The amount codes that come before the digits are explained on the cloud cover codes page, and the way the lowest broken or overcast layer becomes the ceiling is explained on the ceiling page.
How the height is measured
FMH-1 lists the methods in order: a ceilometer where one is available, a ceiling light, or the known heights of hills, towers or other isolated objects within 1 1/2 statute miles of a runway. Without those, the observer estimates the height with a ceiling balloon, pilot reports or experience. At automated stations the ceilometer is the only source, and the reported layers come from an algorithm that processes 30 minutes of its readings. The instrument and its limits are explained on the ceilometer page.
The FAA AIM adds a limit that matters when reading US automated reports: clouds above 12,000 feet cannot be reported by an automated station. A high layer that a human observer would see does not appear in the report at all.
Special values
Four forms replace or modify the usual digits:
000: a base at or very near the surface (50 feet or less in FMH-1, below 100 feet in CAP 746).///in place of the digits: the height is not available. WMO-No. 782 usesBKN///when an automatic system detects a layer but not its base.///at a mountain station: FMH-1 uses it for a layer whose base is below the station level.VVwith three digits: the sky is hidden by an obscuration, and the digits give how far the observer can see upward, not a cloud base. This case is covered on the vertical visibility page.
FMH-1 also allows a remark when a low ceiling varies quickly, such as CIG 005V010, a ceiling varying between 500 and 1,000 feet.
Cloud heights in a TAF
A TAF uses the same three digits and the same reference, the aerodrome. Forecast heights are less precise than observed ones, and WMO-No. 782 defines change groups by thresholds rather than by every step: the lowest broken or overcast base reaching or passing 100, 200, 500, 1,000 or 1,500 feet. A forecaster may write BKN008 in a TEMPO group to describe a base expected somewhere around that height, not exactly at 800 feet.
A schematic report
METAR LXXX 190750Z 27008KT 9000 FEW006 SCT014 BKN075 OVC120 11/09 Q1012
It reads: few clouds at 600 feet, scattered at 1,400 feet, broken at 7,500 feet, overcast at 12,000 feet, all above the aerodrome. In a WMO report the 7,500 foot value is a 100 foot step; in a US report it could stand for any measured value close to it, because FMH-1 uses 500 foot steps there. The ceiling is 7,500 feet, the first broken layer.
In real reports
This page has no "In real reports" box. The height digits appear in almost every report with cloud, so a share of reports would say little. The boxes on the cloud cover and vertical visibility pages show how often each layer code appears in the NOAA Aviation Weather Center sample collected for this site.
Method and limits
The reporting steps and rounding rules are taken from WMO-No. 782 (2025 edition, cloud group), CAP 746 (sections 4.105 and 4.109) and FMH-1 (2019, section 9.4.7 and Table 9-7). The above ground and above mean sea level references and the 12,000 foot limit of automated stations come from the FAA AIM, chapter 7, section 1. The 6,200 and 7,300 foot cases are illustrations of the FMH-1 rule, not quoted examples. The LXXX line is a schematic example, not a real report. The image shows low clouds on a Norwegian island; it is not linked to a specific report.
Training and reference only. For flight planning, always use official briefing sources (your national weather service, AIS or approved provider).
Frequently asked questions
How do I read the cloud height in a METAR?
Multiply the three digits by 100 to get feet. SCT025 is a scattered layer with its base at 2,500 feet, and OVC004 is an overcast layer at 400 feet. The value is the height above the aerodrome, so it can be compared directly with approach minimums expressed as heights.
Is cloud height in a METAR AGL or MSL?
Above ground. The FAA AIM states that ceiling heights are above ground level, and CAP 746 says cloud heights are given above aerodrome level. Pilot reports and area forecasts use mean sea level instead, so the reference depends on the product.
Why does a METAR show 1,800 feet when the cloud is at 1,850?
Heights are rounded down to the next reporting step, never up. WMO-No. 782 gives the example of a layer at 1,850 feet reported as SCT018. Rounding down keeps the reported base at or below the real one, which is the safer side for a pilot.
What does 000 mean in a cloud group?
It means the base is at or very close to the surface. FMH-1 codes layers 50 feet or less above the surface as 000, and CAP 746 uses 000 below 100 feet. A sky hidden by fog is normally coded with a vertical visibility instead.
What do slashes in place of the height mean?
They mean the height is not available. WMO-No. 782 uses BKN/// when an automatic system detects the amount but not the base. In US mountain stations, FMH-1 uses /// for a layer whose base is below the station level.
Sources
- World Meteorological Organization (2025). Aerodrome Reports and Forecasts: A Users' Handbook to the Codes (WMO-No. 782), 2025 edition
- Office of the Federal Coordinator for Meteorology (2019). Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FCM-H1-2019)
- UK Civil Aviation Authority (2023). CAP 746, Requirements for Meteorological Observations at Aerodromes
- Federal Aviation Administration. Aeronautical Information Manual, chapter 7, section 1
- Federal Aviation Administration (2024). Aviation Weather Handbook (FAA-H-8083-28A)